Majestic SA42R Page 27 Installation Manual Download

Page: 27 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Finishing

A. Finishing Material

Refer to Sections 1.B. and Sections 1.C. for combustible/

non-combustible materials. Refer to Figure 7.1 for non-

combustible zone.

WARNING!

Risk of Fire!

You must maintain clear-

ances.

• Do NOT cover metal fireplace front with combustible

materials.

• Install combustible materials only to specified

clearances on top front and side edges.

• Complete framing and apply drywall over framing.

• A bead of 300-deg F minimum non-combustible sealant

must be used to close off any gaps at the top and sides

between the fireplace and drywall to prevent cold air

leaks.

• Only non-combustible materials may be used to cover

the metal fireplace front.

Metal strips are placed 2 in. (51 mm)

under the front of the fireplace and must

extend beyond the front and sides of

fireplace opening by 2 in. (51 mm)

Continuous,

non-combustible sealant

Floor constructed of wood or

other combustible material

HX3 or HX4

Hearth Ext

or equivilent

insulation

Hearth

Refractory

Finished combustible wall

Combustible material

Non-combustible

decorative facing

(up to full brick depth)

2 x 4 header, flush with

front of stand-offs

Tile, stone or other

non-combustible material

Flat 2 x 4 stud wall

Figure 7.2

Decorative Facing

These metal surfaces

may be covered

with non-combustible

material.

300° silicone

sealant around

edge of fireplace

and drywall.

DO NOT put

sheating over

these surfaces.

Figure 7.1 Non-combustible Facing

Note:
If Lintel Bar is used make sure

it does not cover combustible

material.

►

Summary of Contents for SA42R









































Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands

Majestic SA42R, Installation Manual

Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands