Majestic SA42R Page 34 Installation Manual Download

Page: 34 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Unvented Gas Logs

CAUTION!

f an unvented gas appliance is installed in

the fireplace, the gas appliance must only be operated

with the fireplace glass door fully open (if included).

Only unvented gas log sets which have been found to

comply with the standard for unvented room heaters,

ANSI Z211.11.2, are to be installed in this fireplace. If

an unvented gas appliance is installed it must incorpo

rate an automatic shutoff device, and must be installed

in accordance with the National Fuel Gas Code Z223.1,

Latest edition.

B. Wood Burning Inserts

WARNING! Risk of Fire!

Improper installation of wood in-

serts may cause fireplace or chimney system to overheat.

If a wood burning insert is being installed in this fireplace,

Hearth & Home Technologies recommends full reline of

the chimney.

• Cooling air openings at the top of the chimney must not

be obstructed in any manner.

• Hearth & Home Technologies recommends securing the

reline at the top of the flue and using the cap certified for

use with this fireplace system.

Firebox

Repack

insulation

knockout

Combustible

materials

Maintain air clearance

to combustibles.

Gas line

Combustible materials

may be located at zero

clearance to gas line

beyond 4 in. (102 mm)

from fireplace side.

Gas line

1 1/2 in. (38 mm)

air space around

pipe

Refractory

Seal with

fireplace mortar

or non-combust-

ible sealant

4 in.

(102 mm)

Outer shell

of fireplace

Figure 8.1 Gas Line Installation

A. Gas Log/Lighter Provision

WARNING! Fire and/or Asphyxiation Risk!

Use with

solid wood fuel or decorative gas appliance only. Gas fire

generates fumes.

A certified gas log lighter or decorative gas log set can be

installed in this fireplace.

Vented Gas Logs

Fireplace Setup

WARNING! Do Not

operate an unvented gas log set in this

fireplace with the chimney removed.

• Maximum input is 100,000 BTU/hr.

• Decorative gas appliance must be certified to

ANSI

Z21.60/CSA 2.26

“Standard for Decorative Gas

Appliances for Installation in Vented Fireplaces”.

• Must be installed in accordance with the

National Fuel

Gas Code, ANSI Z223.1 and Natural Gas Installation

Code, CAN/CGA-B149.1-M95 or the Propane

Installation Code, CAN/CGA-B149.2-M95.

• A gas log set must incorporate a gas shutoff.

• Gas Log set requires the damper to be locked fully open.

• A listed automatic damper system with safety interlock

may be used in this fireplace with only compatible,

listed gas log sets. See damper system manufacturer’s

instructions.

• Knockouts are provided on both sides of the fireplace

and in refractories for 1/2 in. (13 mm) iron pipe.

• Seal refractory around pipe with fireplace mortar or a

non-combustible sealant.

Summary of Contents for SA42R









































Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands

Majestic SA42R, Installation Manual

Search results

Summary of Contents for SA42R

Reviews:

Related manuals for SA42R

Brands by name

Popular brands