manualshive.com logo in svg

Majestic SA42R, Installation Manual

The Majestic SA42R is a remarkable product that requires careful installation. To ensure a hassle-free setup, we provide a comprehensive installation manual for free download from our website. Our user-friendly manual guarantees a smooth installation process, allowing you to fully enjoy the exceptional features of the Majestic SA42R.

Share
Download
background image

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

16

B. Offsets/Returns

•  Use an offset/return to bypass overhead obstructions.

•  An offset and return can be used as a single entity or separated by chimney section(s).

 WARNING! 

Risk of Fire! DO NOT 

use offset/returns greater than 30°. Chimney draft will be restricted and could cause 

overheating and fire. Secure offsets with screws ( not to exceed 1/2” / 13 mm in length) Secure returns with strapping. 

Straight chimney sections may be secured with screws. Keep chimney sections from separating or twisting.

•  Measure the shift needed to avoid the overhead obstruction. Refer to dimension A in Figure 4.2.

•  Find the appropriate A dimension listed in Table 4.3. The B dimension coinciding with the A dimension measurement in 

Table 4.3 represents the required vertical clearance needed to complete the offset/return.

•  Read across the chart to find the number of chimney sections/model numbers needed between the offset and return.

A

B

1-1/4 in. (32 mm)

OVERLAP

Figure 4.2  Chimney Offset/Return

Table 4.3 Offset Dimensions

Example:

 

Your “A” dimension from Figure 4.2 is 14 1/2 in. (368 

mm). Using Table 4.3 the dimension closest to, but not 

less than 14 1/2 in. (368 mm) is 14 1/2 in. (368 mm) us

-

ing a 30° offset/return. 
You determine from the table that you need 34 1/8 in. 

(867 mm) (Dimension “B”) between the offset and re

-

turn. 

The chimney component that best fits your application is 

one SL324.

15-degree

30-degree

SL306 SL312 SL318 SL324 SL336 SL348

A

B

A

B

in.

mm

in.

mm

in.

mm

in.

mm

1 5/8

41

13 3/8

340

3 5/8

92

15 1/2 394

-

-

-

-

-

-

2 7/8

73

17 3/4

451

5 1/2

140 18 5/8 473

1

-

-

-

-

-

4 1/8

102

22 3/8

568

7 1/4

184 21 3/4 552

2

-

-

-

-

-

4 1/2

114

23 5/8

600

8 1/2

216 23 3/4 603

-

1

-

-

-

-

5 3/4

146

28 1/4

718 10 1/4 260

27

686

1

1

-

-

-

-

6

152

29 3/8

746 11 1/2 292

29

737

-

-

1

-

-

-

7 1/4

184

34

864 13 1/4 337 32 1/8 816

-

2

-

-

-

-

7 3/4

197

36 1/8

918 14 1/2 368 34 1/8 867

-

-

-

1

-

-

8 3/4

222

39 3/4 1010 16 1/4 413 37 3/8 949

1

-

-

1

-

-

10 3/8 264

45 5/8 1159 19 1/4 489 42 1/2 1080

-

-

2

-

-

-

10 5/8 270

46 3/4 1187 20 1/2 521 44 5/8 1133

-

-

-

-

1

-

11 7/8 302

51 3/8 1305 22 1/4 565 47 3/4 1213

1

-

-

-

1

-

13 1/2 243

57 1/4 1454 25 1/4 641 52 7/8 1343

-

-

-

2

-

-

13 3/4 349

58 3/8 1483 26 1/2 673

55

1397

-

-

-

-

-

1

15

381

63

1600 28 1/4 718 58 1/8 1476

1

-

-

-

-

1

16 1/2 419

68 3/4 1746 31 1/4 794 63 1/4 1607

-

1

-

-

-

1

18

457

74 5/8 1895 34 1/4 870 68 1/2 1740

-

-

1

-

-

1

19 5/8 498

80 3/8 2042 37 1/4 946 73 3/4 1873

-

-

-

1

-

1

20 5/8 524

84 1/8 2137 39 1/8 994 76 7/8 1953

1

-

-

1

-

1

22 3/4 578

91 7/8 2334 43 1/4 1099 84 1/8 2137

-

-

-

-

1

1

24

610

96 1/2 2451 45 1/8 1146 87 1/4 2216

1

-

-

-

1

1

25 7/8 657 103 1/2 2629 49 1/4 1251 94 1/2 2400

-

-

-

-

-

2

Proper assembly of air-cooled chimney parts result in an overlap at chimney joints of 1-1/4 in. (32 mm). Effective 

length is built into this chart.

Summary of Contents for SA42R









































Reviews:

No comments

Related manuals for SA42R

barbas UNIVERSAL-6 65 Instructions For Use & Maintenance Manual preview
UNIVERSAL-6 65
Brand: barbas Pages: 32
barbas BOX30 75 Installation And Maintenance Manual preview
BOX30 75
Brand: barbas Pages: 48
Backyard Creations ST. CROIX HD WT17YL Assembly Instructions Manual preview
ST. CROIX HD WT17YL
Brand: Backyard Creations Pages: 13
Living 085-1296-8 Assembly Instructions Manual preview
085-1296-8
Brand: Living Pages: 14
Superior SSDV-3328 Installation Instructions Manual preview
SSDV-3328
Brand: Superior Pages: 36
Dimplex DF1870L Owner'S Manual preview
DF1870L
Brand: Dimplex Pages: 12
Vents FFK 125 User Manual preview
FFK 125
Brand: Vents Pages: 28
Olsberg HKI Leo 28/9251 Instructions Manual preview
HKI Leo 28/9251
Brand: Olsberg Pages: 37
Napoleon GD862KT Installation Instructions preview
GD862KT
Brand: Napoleon Pages: 2
Flavel Caress Slimeline SC FNVC**SN User Instructions preview
Caress Slimeline SC FNVC**SN
Brand: Flavel Pages: 12
Desa VMH1OTNB Owner'S Operation And Installation Manual preview
VMH1OTNB
Brand: Desa Pages: 48
Landmann Brooke Assembly And Use Instructions preview
Brooke
Brand: Landmann Pages: 6
Dimplex 6911580000 Service Manual preview
6911580000
Brand: Dimplex Pages: 22
Desa CDV37N/P Owner'S Operation And Installation Manual preview
CDV37N/P
Brand: Desa Pages: 36
Napoleon Ascent BHD4PFCNA Installation And Operation Manual preview
Ascent BHD4PFCNA
Brand: Napoleon Pages: 140
Jøtul C 350 Winterport Installation Manual preview
C 350 Winterport
Brand: Jøtul Pages: 2
Heat & Glo GEM36 Installer'S Manual preview
GEM36
Brand: Heat & Glo Pages: 26
Nordpeis N-20 T User Manual preview
N-20 T
Brand: Nordpeis Pages: 48

Brands by name

Popular brands

Load more brands