Majestic JADE32IN Page 69 Installation Manual Download

Page: 69 / 69

Majestic • JADE32IN, JADE42IN, JADE42IL Installation Manual • 2491-986 Rev. K

• 10/18

B. Accessories

Remote Controls, Wall Controls and Wall
Switches

After a qualified service technician has installed the re

mote control, wall control or wall switch, follow the in-

structions supplied with the control installed to operate

your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child

protection lockout feature.

• Keep remote controls out of reach of children.
See your dealer if you have questions.

Install approved accessories per instructions included

with accessories. Contact your dealer for a list of ap

proved accessories.

It is recommended that optional accessories are installed

prior to installation of finishing material. The lower cover

panel is removable and provides access for installation of

the optional fan, LED kit and remote control upgrades. If

finishing material is already installed, the optional acces

sories must be installed by removing the basepan, burner

and valve assembly. Use only Hearth & Home Technol

ogies-approved optional accessories with this appliance.

WARNING! Risk of Fire and Electric Shock!

Use ONLY

Hearth & Home Technologies-approved optional acces-

sories with this appliance. Using non-listed accessories

could result in a safety hazard and will void the warranty.

Optional Glass Refractory Kit

An optional glass refractory kit is available for JADE32IN

and JADE42IN/JADE42IL. Follow the instruction supplied

with the kit for installation. Contact your dealer if you have

questions.

Optional Log Kits

Traditional or Driftwood Log kits are available for

JADE32IN and JADE42IN/JADE42IL. Follow the instruc

tions supplied with the kit for installation. Contact your

dealer if you have questions.

Optional LED Kit

An optional LED lighting kit is available for JADE32IN and

JADE42IN/JADE42IL. Follow the instructions supplied

with the kit for installation and operation. Contact your

dealer if you have questions.

Majestic, a brand of Hearth & Home Technologies

7571 215

Street West, Lakeville, MN 55044

www.majesticproducts.com

Please contact your Majestic dealer with any questions or concerns.

For the location of your nearest Majestic dealer,

please visit www.majesticproducts.com.

Optional Stones Kit

An optional stones kit is available for use with the JADE32IN

and JADE42IN/JADE42IL models. Follow the instructions

supplied with the kit for installation. Contact your dealer if
you have questions.

Optional Fan

After a qualified service technician has installed the fan,

follow the instructions supplied with the fan kit to operate

your fan. Contact your dealer if you have questions.

Note:

The optional fan can not be used with the Smart-

Wall™ TV Kit.

Optional Heat Management Systems

After a qualified service technician has installed the Heat-

Zone

-Gas, Smart-Wall™ TV Kit, Heat-Duct Kit, or Heat-

Out-Gas Kit, follow the instructions supplied with the kit for

operation. Contact your dealer if you have questions.

Note:

Optional heat management systems kit must be

installed while the sides of the appliance are accessible.

Note:

The Smart-Wall™ TV Kit can not be used with an

optional fan or Power Vent.

Summary of Contents for JADE32IN






































































Search results

Summary of Contents for JADE32IN

Reviews:

Related manuals for JADE32IN

Brands by name

Popular brands

Majestic JADE32IN, Installation Manual

Search results

Summary of Contents for JADE32IN

Reviews:

Related manuals for JADE32IN

Brands by name

Popular brands