Majestic 400DVKHL Installation And Operating Instructions Manual Download Page 58

Page: 58 / 64

73D0129

DVKHL Series Gas Fireplace

repLaceMent partS

SIGnature cOMManD SySteM

Item

Description

qty. 400DVKHLntSc 400DVKHLptSc 500DVKHLntSc 500DVKHLptSc

Gas Valve Assembly

80D0001

80D0002

80D0001

80D0002

Pilot Assembly

80D0039

80D0040

80D0039

80D0040

Control Box

80D0037

80D0038

80D0037

80D0038

Command Center

80D0005

5a.

Tube, Rear, Venturi

73D349K

73D3549K

54D0564

5b.

Tube, Front, Venturi

73D0562K

43D0185

43D1085

5c.

Rear Tube, Tee to Solenoid

73D3529K

5d.

Rear Tube, Solenoid to Venturi

73D3528K

5e.

Tube, Front, Through-wall

73D0146K

73D0146

Flexhose w/Shutoff Valve

69D0030

7a.

Rear Injector

58D0102

58D0052

57D0679

57D0680

7b.

Front Injector

57D0612

58D0056

56D3059

62D3005

8a.

Rear Burner Assembly

73D3270

73D3268

8b.

Front Burner Assembly

73D3269

73D3267

Venturi

45D0600

10.

Wire Valve/Control (not shown)

80D0010

11.

Wire AC Module (not shown)

80D0009

Wire Command Ctr. (not shown)

80D0008

13.

Remote Transmitter (full function) 1

TSFRSC

14.

AC Module

SCSACM

15.

Solenoid (not shown)

73D3007

accessories

16.

Forged Andiron 13"

FA113

17.

Cast Iron 12

CAI121/2

18.

SCS Wall Extension Kit

SCSWEK

(15' Wire, Rough-in Box, Wall Cover)

19.

Decorative Door Kit

KHL400ADBT

KHL500ADBT

Fuel conversion Kits - Signature command System
natural Gas to Lp

400DVKHL

Kit #KHL400CKPS

500DVKHL

Kit #KHL500CKPS

Lp to natural Gas

400DVKHL

Kit #KHL400CKNS

500DVKHL

Kit #KHL500CKNS

Summary of Contents for 400DVKHL

































































Search results

Summary of Contents for 400DVKHL

Reviews:

Related manuals for 400DVKHL

Brands by name

Popular brands

Majestic 400DVKHL, Installation And Operating Instructions Manual

Search results

Summary of Contents for 400DVKHL

Reviews:

Related manuals for 400DVKHL

Brands by name

Popular brands