Majestic 360DVS3 Homeowner'S Installation And Operating Manual Download Page 6

Page: 6 / 31

360DVS Series Direct Vent Fireplaces

10006326

CFM123_360DVS3_dims_RV2

REAR VENT CONFIGURATION

8/10/00

rev. 8-23-02 rjs

ROD

ROW

ROD

ROH

ROD

360DVSL

360DVS/3/L/R

360DVS3

360DVSR

CFM124_360DVS3_TV2

TOP VENT CONFIGURATION

8/10/00

rev. 8-23-02 rjs

ROD

ROH

ROW

ROH

ROD

360DVSL

360DVS/3/L/R

360DVS3

360DVSR

Framing Dimensions - 360DVS3 / 360DVSL / 360DVSR

Rear Vent Conﬁration

Top Vent Conﬁguration

CFM123

CFM124

Framing Dimensions

Ref.

Rear Vent Conﬁguration

Top Vent Conﬁguration

Model

360DVS3

360DVSL/R

360DVS3

360DVSL/R

ROD

(See Note 1)

(See Note 2)

(See Note 1)

( See Note 2)

ROH

⁵⁄₈

” (981 mm)

Not to be framed until unit is set in place, due

to 3

¹⁄₈

” (79 mm) allowance for ﬂue collar

ROW

⁵⁄₈

” (1032 mm) minus one time (1x) ﬁnishing material thickness to be even with face of unit.

Fig. 3b

Fireplace framing dimensions—360DVS3/ 360DVSL/ 360DVSR

NOTE 1:

24” (610 mm) minus two times (2x) ﬁnishing material thickness to be even with face of unit.

NOTE 2:

³⁄₄

” (629 mm) minus one time (1x) ﬁnishing material thickness to be even with face of unit.

Summary of Contents for 360DVS3
































Search results

Summary of Contents for 360DVS3

Reviews:

Related manuals for 360DVS3

Brands by name

Popular brands

Majestic 360DVS3, Homeowner'S Installation And Operating Manual

Search results

Summary of Contents for 360DVS3

Reviews:

Related manuals for 360DVS3

Brands by name

Popular brands