background image

21

DVRTSB Bay Window Fireplace

10003848

 

Only glass approved by CFM Corporation should be 
used on this fireplace.

• 

The use of any non-approved replacement glass  
will void all product warranties.

• 

Care must be taken to avoid breakage of the glass.

• 

Under no circumstances should this appliance be 
operated without the front glass in place, or with the 
glass in a damaged condition.

• 

Replacement glass (complete with gasket) is 
available through your Majestic Fireplaces dealer 
and should only be installed by a licensed qualified 
service person. 

   

• 

The top side and top end louvres are removed by  
simply lifting the louvre assembly and pulling the  
assembly away from the fireplace. (Fig. 35)

• 

The lower side louvres are hinged along the lower 
edge and are folded down for access to components 
in the base cavity of the fireplace.

• 

The lower end louvre assemblies on the DVRTSB  
unit are removed in the same manner as the top 
louvre assemblies.

6.  Tilt the lower edge of frame out slightly and lift  

glass/frame assembly up and away from the 
fireplace. (Fig. 36)

7.  To reinstall the glass panel reverse this procedure.

Operating Instructions

Glass Information

Glass/Frame Removal 

Louvre Removal

1.

2.

Louvre

Glass Panel

FP1390

Fig. 35

  Louvre removal.

  Front Glass Frame

 

1.  Shut off the gas supply.
2.  Allow the fireplace to cool if it has been in operation.
3.  Remove the top louvre assembly.
4.  Lower the bottom louvre assembly.
5.  Release the two clamps along lower edge of the  

frame by pulling down on clamp handles. (Fig. 36)

Lower Clamps

Window  

Frame

Pull Clamp 

Hook

Push 

Clamp 

Handle

Window 

Frame

FP1391

Fig. 36

  Remove glass/frame assembly.

 

Side Glass Frame 

1.  Remove the top and bottom louvre assemblies.
2.  Remove the lower window trim (held in place   

with magnets).

3.  Remove both lower retaining screws. Access to  

these screws is gained through the holes along the  
lower edge of the frame behind the trim. (Fig. 37)

4.  Tilt lower edge of frame out slightly and lift glass/ 

frame assembly up and away from the fireplace. 

5.  To reinstall the glass panel reverse the process. 

Location of Lower 

Retaining Screws

FP1392

Fig. 37

  Remove end glass.

Summary of Contents for DVRTSB





































Reviews: