background image

MIGE3028-4GF Serial Rack Mounted Industrial Ethernet Switch

I

Trademark

This trademark is owned by Wuhan Maiwe

Communication Co., Ltd.

Mwring

is the trademark used for link redundancy and self-recovery

technology, owned by Wuhan Maiwe Communication Co., Ltd.

Microsoft

and

Windows

is registered trademark owned by Microsoft.

Copyright

Copyright © Wuhan Maiwe Communication Co., Ltd.

Clarification

The user manual is applicable to MIGE3028-4GF series managed rack
industrial ethernet switch.
Please read the following license agreement carefully before using this manual.
The products described in this manual can be used only if you agree on the
following license agreement.

Important Statement

Any information provided by our company in this manual does not represent for
corresponding authorization on these information.
Our company attempts to ensure the accuracy and applicability for the
information provided in this manual, however our company does not assume
any responsibility for the use of these information, and does not assume any
joint responsibility for the use of these information. There may be a few
technical or typographical errors in the product and manual. The company
reserves the right to change all or part of this manual without prior notice.

Statement
Due to continuous update and improvement of products and
technology, the contents of this document may not be completely
consistent with the actual products, appreciate for your understanding.
If necessary to inquiry the updates of the product, please check our
official website or contact our representative directly.

Revision history:

Version

Date

Reason

V1.0

2016.1

Document creation

Summary of Contents for MIGE3028-4GF






















Reviews: