background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

3

Part No. 5000893

Introduction & User Information

Introduction and User Information

Samples of the Main multipoint water heaters have 
been examined by Advantica Technologies Limited, a
United Kingdom Notified Body. The range is certified
to comply with the essential requirements of the Gas
Appliance Directive 90/396/EEC and are therefore 
permitted to carry the CE Mark.

This appliance is not suitable for use with a swivel 
spout.

This appliance is room sealed instantaneous water 
heater designed to supply hot water to several taps 
which may be situated in different rooms, but not 
necessarily at the same time.

The pilot is lit by a piezo spark igniter; batteries or 
electricity are not required.

The main burners will automatically light when a 
domestic hot water tap is turned on and go out when
the tap is turned off.

Ensure that the clearances shown in (Page 7,
Installers section) are maintained at all times.

Please take time to read through these 
instructions to familiarise yourself with the water
heater.

This appliance contains an energy cut-off device that
will shut down the gas supply to the appliance if the 
water in the heat exchanger exceeds the anticipated
temperature limit. Although intended to guard against
an internal fault, it may be triggered inadvertently by
other causes, especially during the summer months 
when the inlet water temperature is unusually high.
Allow the appliance to cool before re-lighting.

WARNING:

If the energy cut-off device is reacting to an 
internal fault, the shut down may be accompanied
by noises from the heat exchanger and pipework,
and it is possible that STEAM will come out of the
hot tap when turned on. If this occurs, arrange for
the appliance to be serviced.

Your installer/engineer will recommend 
replacement of the Pressure Relief Valve 
Assembly to ensure continued safety.

Running Costs. To work out the approximate running 
costs per hour for this fire, perform the following 
calculation:-

Heat Input in kW x Cost Per kWh
= Running Cost Per Hour

Heat inputs for the various settings are shown in the 
Technical Data & Costs per kWh are shown on your 
gas bill.

Washing Machines

Information regarding the use of washing machines 
with this appliance is shown at the rear of these 
instructions.

Shower Systems

Information regarding the use of shower systems 
with this appliance is shown at the rear of these 
instructions. In hard water areas, shower roses may 
require regular cleaning as scale my form and restrict
the flow of water.

The 

Mersey Super is Not

suitable for use

with a shower system.

WARNING:

The Outer Case of this Appliance MUST BE 
CORRECTLY positioned and secured in 
place before any attempt is made to light the
burners. If in doubt, call your Installer.

IMPORTANT:

If it is known or suspected that a fault exists
on the appliance, it must not be used until 
the fault has been corrected by a competent
person.

REPLACEMENT PARTS:

WARNING: The use of replacement parts on
this appliance which are not recommended 
by Potterton may affect the product safety,
performance and warranty.

We recommend that replacement parts be 
obtained only from Curzon branches or 
other recognised Potterton spares outlets.

Summary of Contents for Mersey Super





































Reviews: