manualshive.com logo in svg

Maico ER-AP, Installation And Operating Instructions Manual

Share
Download
Maico ER-AP Installation And Operating Instructions Manual Download Page 2

Table of contents

2

Table of contents

1

Scope of delivery ..................................

4

2

Additional information .........................

4

3

Specialist installer qualifications ........

4

4

Intended use..........................................

4

5

Safety instructions and warnings .......

4

6

Safety instructions ...............................

5

6.1 General safety instructions .............

5

6.2 Safety instructions regarding in-

stallation, operation, cleaning and
maintenance ...................................

5

7

System and product information ........

8

7.1 Certificates of approval...................

8

7.2 Installation conditions .....................

8

7.3 Permitted exhaust air systems .......

9

7.4 Unit versions...................................

9

7.4.1

Product features.............

9

7.4.2

Controls (circuit board
types) .............................

10

8

Technical data .......................................

10

8.1 Environmental conditions and oper-

ating limits.......................................

10

8.2 Regulations for operation with fire-

places .............................................

10

8.3 Technical data table .......................

10

8.4 Storage ...........................................

10

9

Mounting preparations .........................

10

9.1 Requirements in line with approval.

11

9.1.1

Approval provisions........

11

9.2 Permitted installation positions: ......

11

9.3 ER-APB: Preparations for installa-

tion with fire protection require-
ments..............................................

12

9.3.1

Preparations for ER-APB
wall installation (with fire
protection) ......................

12

9.3.2

Preparations for the ER-
APB ceiling installation
(with fire protection)........

12

9.4 Preparations for wall, shaft or ceil-

ing installation without fire protec-
tion..................................................

14

9.5 Preparations for the electrical con-

nection ............................................

14

9.6 ER-APB shut-off device, ER-AP

shutter.............................................

15

10 Housing installation .............................

15

10.1 Wall installation, lower part of

housing............................................

15

10.2 Ceiling installation, lower part of

housing............................................

17

11 Electrical connection ............................ 18

12 Installation of fan insert and upper

part of housing ......................................

19

13 Commissioning...................................... 20

14 Cleaning, maintenance ......................... 21

15 Fault rectification................................... 21

16 Spare parts ............................................. 22

17 System and accessory components ... 23

18 Removing the housing .......................... 23

19 Environmentally responsible dis-

posal .......................................................

24

20 Wiring diagrams .................................... 24

Summary of Contents for ER-AP

































Reviews:

No comments

Brands by name

Popular brands

Load more brands