background image

2

INTRODUCTION

TO THE PURCHASER 

This new accessory was carefully designed to give  years of dependable service. This manual has been provided to 
assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but 
are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize  yourself  fully  with  the  safety  recommendations  and  operating  procedures  before  putting  the  machine  to 
use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will 
use this attachment.

THIS  SAFETY  ALERT  SYMBOL  IDENTIFIES  AN  IMPORTANT  SAFETY  MESSAGE  IN  THIS 
MANUAL  THAT  HELPS  YOU  AND  OTHERS  AVOID  PERSONAL  INJURY  OR  EVEN  DEATH. 
DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF 
HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER:

Signals an extreme hazard that will cause serious injury or death if recommended precautions 
are not followed.

WARNING:

Signals  a  hazard  that  may  cause  serious  injury  or  death  if  the  recommended  precautions  are 
not followed.

CAUTION:

Signals a hazard that may cause minor or moderate injury if the recommended precautions are 
not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on 
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement 
parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer 
for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the 

bag and the list of the box.

SERIAL NUMBER :

___________________________

(IF APPLICABLE)

MODEL NUMBER:

___________________________

PURCHASE DATE :

___________________________

Summary of Contents for 700624-2





























Reviews: