background image

MAHA Maschinenbau Haldenwang GmbH & Co. KG ꞏ Hoyen 20 ꞏ 87490 Haldenwang ꞏ Germany 

Phone +49 8374 585-0 | Fax +49 8374 585-590 | Mail [email protected] | Web www.maha.de 

 

Original EC Declaration of Conformity 

CE364601-en 

 

 
 

MAHA Maschinenbau Haldenwang GmbH & Co. KG 

herewith declares as a manufacturer its sole responsibility to ensure that the product named hereafter meets the 
safety and health regulations both in design and construction required by the directives stated below. 
This declaration becomes void if any change is made to the product that was not discussed and approved by 
named company beforehand. 
 

Model 

VP Number 

MA STAR 5.5 

VP VP 451187 

MA STAR 5.5 MB 

VP 451188 

 

Designation 

Two Post Lift 
Rated Load Capacity: 5500 kg 
 

Directives 

2006/42/EC 
2014/30/EU 
 

Standards 

DIN EN 1493:2010 
DIN EN 60204-1 
DIN EN ISO 13849-1 
 

Person Authorised to Compile the Technical File 

Ralf Kerkmeier 
MAHA Maschinenbau Haldenwang GmbH & Co. KG, Hoyen 20, 87490 Haldenwang, Germany 
 

 
 

Haldenwang, 2021-07-12 

Andreas Maier 
Head of Mechanical Development 

 

Summary of Contents for MA STAR 5.5




































Reviews: