background image

 

 

 

 

 

 

 

 

 

 

            

   

 

 

 

 

 

 

Exclusions: 

Routine maintenance/replacement parts are excluded from the warranty. These include, but are not limited to: hoses, desiccant, filters, filter 
elements, wiper seals, gaskets, dew point sensors, infrared lamps, motors, internal solenoids, fuses and motor brushes. Use with abrasive 
materials will void the warranty of any standard product.  Wear resistant options may be available to extend usable service life with abrasive 
materials.

 

Novatec reserves the right to limit the warranty if the customer installs replacement parts that do not meet the specifications of the 

original parts supplied by Novatec. 

*Specific Exclusions: 

1. 

NovaDrier™  and 

NITROdry

™  warranty is void if coalescing filters are not replaced on a 6-month or yearly basis (per 

instruction manual) and/or membrane has been exposed to ozone. 

2.     NovaVac Dryer -The ability of the canisters to hold vacuum will be compromised if the vacuum seal edge is damaged  
        from mishandling. We do not warranty canisters damaged from improper handling. We do, however, warranty the seals. 
3.     LOAD CELLS on our WSB’s are covered by Novatec standard warranty as long as they have not been damaged from  
 

improper handling. 

4.     Desiccant Wheel Warranty will be void if the wheel has been exposed to plasticizer, dust or other contaminants as a result 

of negligence on the part of the processor. 

5.     - We assume no responsibility from equipment failures resulting from untreated or improperly treated water. 
 

 

  

This warranty shall not apply to equipment:  

1. 

Repaired or altered without written approval of NOVATEC unless such repair or alteration 
was, in our judgment, not responsible for the failure 

2. 

Which has been subject to misuse, negligence, accident or incorrect wiring by others 

3. 

Warranty is void if processing rates exceed manufacturer-recommended levels or if damage is caused by 

ineffective power isolation and/or power spikes/sags or incorrect installation. 
 

NOTE: All conditions and content of this warranty are subject to changes without notice. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for NOVATEC NDB Series

















Reviews: