Magnum 261815 Operation Download

Page: 1 / 84

Operation

™

, X7

™

, ProX7

™

& ProX9

™

Airless Sprayers

312001P

- For portable spray applications of architectural paints and coatings -

X5 & X7 Models ONLY: Use water-based or min-
eral spirit-type materials only. Do not use materi-
als having flash points lower than 70° F (21° C).
For more information about your material, request
MSDS from distributor or retailer.

Models 262800, 262805, 261815, 261820

See page 2 for model and series information including
dispense rate, recommended hose length, guns, and
maximum working pressure.

IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this
manual. Save these instructions.

AGNUM

Model: 262800

ti11304a

Series D

AGNUM

Model: 262805

ti11305a

Series C

AGNUM

ProX7

Model: 261815

ti9369b

Series B

AGNUM

ProX9

Model: 261820
Series B

ti16976a

The manual provided with
this sprayer contains
English and Español.

Visit our website;
http://M

AGNUM

.Graco.com

Summary of Contents for 261815





















































































Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands

Magnum 261815, Operation

Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands