8
GB
Dear MAGNAT Customer,
The BLACK CORE FIVE car hi-fi power amplifier will enable you to satisfy your high demands on sound reproduction in your car. With its
impressive deep-bass power reserves, low harmonic content and neutral reproduction, the BLACK CORE FIVE takes car hi-fi to new
heights. The amplifier is characterized by low operating current, rapid switching capabilities and excellent temperature stability. Experience
and enjoy how this high-tech machine perfectly reproduces magnificent sound.
Please read all of the owner’s manual before installing and using the amplifier.
1. TECHNICAL DATA
Channels 1-4
Channel 5
Stereo
/ Bridged
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
4 x 200 W / 2 x 600 W
600 W
on 4 Ohm
Nominal output power (DIN 45 324, B+=14.4V)
4 x 65 W / 2 x 200 W
200 W
on 4 Ohm
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
4 x 300 W
900 W
on 2 Ohm
Nominal output power (DIN 45 324, B+=14.4V)
4 x 100 W
300 W
on 2 Ohm
Loudspeaker impedance (stereo)
2 – 8 Ohm
Frequency response
5 – 50 000 Hz (-3 dB)
Total harmonic content (DIN 45 403)
< 0.05% (1 kHz, channels 1 – 4)
< 0.08% (100 Hz, channel 5)
Stereo separation (IEC 581 )
> 60 dB (1 kHz)
Weighted noise distance (IEC A)
> 100 dB
Input sensitivity LOW LEVEL INPUT
200 mV – 6 V
Input impedance LOW LEVEL INPUT
20 kOhm
Channels 1 and 2: high-pass filter
15 – 5000 Hz (12 dB per octave)
Channels 3 and 4: high-pass filter
15 – 800 Hz (12 dB per octave)
low-pass filter
250 – 5000 Hz (12 dB per octave)
Channel 5:
low-pass filter
30 – 150 Hz (12 dB per octave)
Bass Boost
0…12 dB at 45 Hz
Power supply
+12 V (10 – 14.4 V), negative to ground
Fuse
70 A Maxifuse
Dimensions (W x H x D)
559 x 54 x 215 mm
Weight
5.6 kg
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
2. OUTSTANDING FEATURES
• High-pass filter with continuously adjustable crossover frequency for channels 1 and 2
• High-pass and low-pass filters (band-pass) with continuously adjustable crossover frequency for channels 3 and 4
• Electronic protection against short-circuit, DC offset and overheating
• Muting circuit suppresses power-on pop
• Sealed screw terminals for speaker and power supply connection
•
Status indicator (green LED) and overload indicator (red LED)
• Channel 5:
• Low-pass (subwoofer) filter with infinitely adjustable separating frequencies
• Infinitely adjustable bass equalization
• Remote control for volume control
3. IMPORTANT INFORMATION – PLEASE READ BEFORE INSTALLING!
• This amplifier is designed
exclusively
for use with 12 V power supplies and negative ground. Do
not
attempt to use it with any other
power supplies!
• The amplifier must be installed in location with adequate air circulation to dissipate the heat generated during operation. Make very
sure that the cooling fins of the heat sinks are not near or pressing against any panels or other surfaces that could obstruct the air
circulation – this is very important. Do
not
install the amplifier in small, enclosed or unventilated areas (for example the spare wheel
recess). The best location is probably in the boot of the car.
• Install the amplifier so that it has maximum protection against vibration, dust and dirt.
• Make sure that the input and output connection cables are installed far enough away from the power supply cables. Routing the power
and signal cables too close together can cause interference.
• Make sure that you install the amplifier in a location where the fuse(s) and controls are accessible.
• Installing the amplifier properly is crucial for the performance and reliability of your sound system. When in doubt it is always advisable
to have the amplifier installed by a qualified technician, especially if it is part of a system with multiple loudspeakers or a complex multi-
channel system.
4. CONNECTIONS
4.1 POWER SUPPLY AND AUTO-ON FUNCTION
IMPORTANT: TO PREVENT THE RISK OF SHORT CIRCUITS DISCONNECT THE CONNECTION CABLE FROM THE POSITIVE POLE
OF THE CAR BATTERY BEFORE YOU START INSTALLING THE AMPLIFIER.
The power cabling usually installed in on-board car networks is not sufficient for a power amplifier’s demands. Make sure that the power
lines to GND and to the +12 V terminal have been sufficiently specified. A cable cross-section of at least 20 mm² must be used to connect
the battery to the amplifier’s terminals.
130.com.ua
Autogood products Internet store “130”
Summary of Contents for BLACK CORE FIVE
