Magnadyne PL50 Installation Manual Download Page 11

11

87

86

85

30

White Wire with

Black Stripe

(SPST ALA984H 

Relay Not Supplied)

Output to Power Trunk Switch

To Co12 Volts

Input to Relay (+ or -)

Insert White Wire with Black Stripe 

 into the Eighth Socket

#2 Button Power Trunk Activation Using Optional 30 Amp Relay

Red Wire 

ALA-RPT

Relay Pack

Orange Wire

Output to Trunk Switch

Purple Wire

Input to Relay (+ or -)

Insert Red Wire into the First Socket

Insert Black Wire into the Eighth Socket

Black Wire 

#2 Button Power Trunk Activation Using Optional ALA-RPT Relay Pack

Dome Light Supervision Using Optional 30 Amp Relay:

(Applies to PL50 Only)

87

86

85

30

Orange Wire 

(SPST ALA984H 

Relay Not Supplied)

Output to Dome Light (+ or -)

To Co12 Volts

Input to Relay (+ or -)

Insert Orange Wire into 

the First Socket

Step 5: Optional Accessory Connections 

(Continued)

Dome Light Supervision Using Optional ALA-RPT Relay Pack: 

(Applies to PL50 Only)

Red Wire 

ALA-RPT

Relay Pack

Orange Wire

Output to Dome Light (+ or -)

Purple Wire

Input to Relay (+ or -)

Insert Black Wire into the First Socket

Insert Red Wire into the Second Socket

Black Wire 

Dome Light Supervision:

(Applies to PL60 Only)

Orange Wire Output to Dome Light (+ or -)

White Wire with Black Stripe Input to Relay (+ or -)

Insert Orange Wire into the First Socket

Insert White/Black Wire into the Second Socket

Summary of Contents for PL50





















Reviews: