Index
Step 1: Component Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Step 2: 10-Pin Main Harness Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
Step 3: 5-Pin Power Harness Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Step 4: Wire Loop Programming . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Step 5: Optional Accessory Connections
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8
Step 6: Transmitter Programming
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-10
Step 7: Remote Feature Programming
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-11
Step 8: Multiple Car Programming
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Step 9: General Testing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Step 10: Speciality Feature and Optional Equipment Testing
. . . . . . . . . . . . . . . . . . . . . . . .
13-15
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Wiring Diagrams
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Step 1: Component Installation
Mounting the Control Module:
Find a suitable location to secure the alarm control module within the passengers compartment of the
vehicle. Never mount the alarm control module in the engine compartment or in the trunk. In addition,
never mount the alarm control module in the direct path of the heater. Secure the alarm control module
by using wire ties or drill two 1/8” holes and secure the module to the frame of the vehicle with the
screws provided.
Mounting the Siren:
Find a suitable location in the engine compartment to secure the siren. Select a location that provides a
direct sound path to the ground for maximum siren output. Use the self tapping screws provided and
secure the siren. Connect the black wire coming from the siren to the frame of the vehicle. In many
cases, you can ground the black wire to one of the screws used to secure the siren. Run the remaining
brown wire through the fire wall to the location of the alarm control module.
Installing Hood/ Trunk Pin Switches:
Provided with the alarm kit is one pin switch and one mounting bracket. To install the switch either in the
truck or under the hood, find a suitable location where the switch will make contact with the hood or
trunk lid and will not get wet. Use the bracket provided or drill a 1/4” hole in the desired location.
Mounting the Override / Valet Switch:
Mount this switch in a hidden but accessible location within reach of the driver of the vehicle. Drill a 1/4”
hole and use the nuts and washers provided to secure the switch. Run the wires from the switch to the
alarm control housing location.
Installing the Alarm Status LED:
The LED indicator provided utilizes a push in type mounting. Drill a 5/16” hole in the desired location,
feed the wires through the hole and push the LED into place. Run the wires to the location of the alarm
control module.
2
Warning ! Do not plug the 10-pin or 5-pin wire harness into the alarm control module before you begin
installing the alarm. The wire harnesses must be plugged into the alarm control module after all
connections are made. Failure to follow this procedure could cause some confusion with transmitter
operation and or alarm function operation.
