background image

MAGICFX® SWIRLFAN II 

 

User and Installation Manual

  7

1.4 

DMX CONTROL

The MAGICFX

®

 SWIRLFAN II is controlled with 1 safety adress and 1 operational 

address. 

DMX Address

Address range

Safety address

1 – 255

Start address (Effect density)

1 – 255

DMX addresses

The safety address cannot be the same as the operational address. Operating of 
these addresses results in the following:

DMX Address

DMX Value (decimal)

Result

Safety address

0

99

Device disabled

100

154

Device enabled

155

255

Device disabled

Start address 

(Effect density)

0

9

No output

10

255

Variable confetti output

Operation of the DMX addresses

When you link multiple machines with DMX, we advise you to use the same Safety 
address for all machines.

CAUTION

Always plug in a DMX Terminator into the DMX output of the final 

unit in the control sequence. Using a DMX Terminator improves 

signal reliability. 

1.5 

DISPLAY PANEL

INFORMATION
ERROR HISTORY

CONFIGURATION

DMX/RDM SETTINGS

Display panel

The display panel is located on the backside of the MAGICFX

®

 SWIRLFAN II. Check the 

following menu structure for all options in the menu. Use the buttons for navigation 

and selection. The left-hand LED blinks red when DMX is active. The right-hand LED 

continuously lights red when an error is present.

Summary of Contents for SWIRLFAN II

























Reviews: