background image

MAGICFX

®

 STADIUMSHOT III 

 

User and Installation Manual

  13

1.8 

INPUT & OUTPUT

The output pipe has a payload of 5 litres and can be filled with MAGICFX

®

 confetti or 

streamers. The maximum load per shot depends on the type of input material. The 
output distance depends on the type of input material and the load. 

Consumable

Amount

Max. Output 

distance

Min. Pressure

MAGICFX

®

 PAPER CONFETTI

2 kg

20 m

66 ft

4 bar

58 psi

MAGICFX

®

 METALLIC CONFETTI

3 kg

20 m

66 ft

4 bar

58 psi

MAGICFX

®

 STREAMERS 20 m x 5 cm

8 Polybags

40 m

131 ft

8 bar

116 psi

MAGICFX

®

 STREAMERS 20 m x 2.5 cm 9 Polybags

40 m

131 ft

8 bar

116 psi

MAGICFX

®

 STREAMERS 10 m x 5 cm

15 Polybags 35 m

115 ft

8 bar

116 psi

MAGICFX

®

 STREAMERS 10 m x 2.5 cm 18 Polybags 35 m

115 ft

8 bar

116 psi

MAGICFX

®

 STREAMERS 10 m x 1.5 cm 20 Polybags 35 m

115 ft

8 bar

116 psi

Projectile types and related loads and output

WARNING

Always shoot streamers at a minimum of 8 bar pressure to unfold 

them completely. Shooting streamers at a lower pressure can 

lead to death or serious injury.

WARNING

Using any other objects other then MAGICFX

® 

CONFETTI or 

STREAMERS or other approved MAGICFX

® 

consumables can lead 

to death or serious injury.

NOTICE

Wind and other weather circumstances will influence the output 

distance. The given values are estimated values.

Summary of Contents for MFX0408









































Reviews: