49
|
Manual de Servicio
Ingenieria de Servicio
Fa
ilu
re
nu
m
be
r
Di
sp
lay
Fa
ult
Co
de
L
a
u
n
d
r
y
C
e
n
t
e
r
Fault description
Recommended Action
Vo
lat
ile
/
No
n-
vo
lat
ile
Lid
stat
us
duri
ng
failu
re
Automatic fault
reset
Possible cause
1
E1
N
A
Speed > 60 rpm in
Speed Sensor with
Lid unlocked
NA
No
n
Vo
lat
ile
NA
NA
NA
2
E2
N
A
Motor turned off &
speed does not
slow down
NA
No
n
Vo
lat
ile
NA
NA
NA
3
E3
X Motor turned on &
Speed Sensor
does not detect
movement
* Reset Non-Volatile fault
* Check that the transmission is not
forced
* Check that clothes are not stuck
* Running service mode routine (test
9), if you have E3 again check
following points:
a) Verify that Speed Sensor is
connected
b) Check the motor and capacitor are
connected
c) Check Motor thermal protection,
check Motor has continuity.
* If the above points are correct, then
monitor a wash cycle to verify that
everything works correctly.
No
n
Vo
lat
ile
lock
ed
Every minute it
generates a
routine to
search for
pulses.
The fault
recovers if it
reads 10 pulses.
A) Sped Sensor does not
connect, bad assembly,
harness damaged
B) Motor thermal protection
opened.
C) Capacitor o motor
unplugged
D) Clothes stuck in Basket
or Agitator
E) Transmission damaged
4
E4
X The lid lock does
not lock or unlock
after 40 seconds
* Reset Non-Volatile fault
*
Verify that the lid is completely
closed and that the lid actuator is not
broken.
*
Run routine in service mode (test 5)
and if it fails, check:
a) Verify connections to Lid Lock and
control board
*
Run routine in service mode again
(test 5) in case of failure change lid
lock,
*
Run routine in service mode again
(test 5) in case of failure change
control board
Vo
lat
ile
Unlo
cked
When lid lock
voltage
feedback is
detected
A)
Lid lock damaged
B)
Lid lock bad connection
C)
Lid lock Harness
damaged
D)
Lid misaligned and
actuator does not adjust.
5
E5
X Speed > 1000 rpm
* Reset Non-Volatile fault.
* Check that the band is assembled
correctly.
* Running a manual cycle "only spin".
No
n
Vo
lat
ile
lock
ed
When reading
zero speed
A) Band disassembly
B) Motor pulley
loose nut
B) Transmission pulley
loose nut
6
E6
X Safety relay short
circuit
* Reset Non-Volatile fault
* Wait 10 seconds
* Running service mode routine (test
9), if you have E6 change Control
Board
No
n
Vo
lat
ile
lock
ed
Every minute a
routine is done
to validate the
operation of the
relay
A) basket moving at the
beginning of the cycle
DISPLAY TEST AND
FAULT CHART
Summary of Contents for Centauro CLGG70214 Series
