background image

R7L-TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-7804-B  Rev.8  P. 10 / 19

• Configuration Properties

CONFIGURATION
PROPERTY

NETWORK 
VARIABLE

TYPE
{ Range }
{ Default }

EXPLANATIONS

SCPTsceneNmbr

----

{}
{0...12}
{0}

Input sensor type for Input 0 through 3
0 : K (CA)
1 : E (CRC)
2 : J (IC)
3 : T (CC)
4 : B (RH)
5 : R
6 : S
7 : C (WRe 5-26)
8 : N
9 : U
10 : L
11 : P (Platinel II)
12 : (PR)

SCPTnvType

nvoTSVal

{SNVT_nv_type}
{}
{SNVT_temp}

Indicates nvoTSVal type.
For use with LonMaker and other tools.

SCPTminDel-
taTemp

nvoTSVal

{SNVT_temp_p}
{1.0...327.66}
{5.00}

Minimum deviation required to send out the network vari-
able.

SCPToffset[0]

nvoTSVal

Same as nvoTSVal

Reference temperature point to adjust the offset

SCPToffset[1]

nvoTSVal

Same as nvoTSVal

Temperature value to output when the reference tempera-
ture set at SCPToffset[0] is input.
Offset = SCPToffset[1] – SCPToffset[0]

SCPTdefScale

nvoTSVal

{SNVT_lev_percent}
{80.000...120.000}
{0.0}

Gain applied to SCPToffset[0]

SCPTsetpoint[0]

nvoTSVal

Same as nvoTSVal

nvoTSVal lower range temperature
SCPTsetpoint[0] < SCPTsetpoint[1]

SCPTsetpoint[1]

nvoTSVal

Same as nvoTSVal

nvoTSVal upper range temperature
SCPTsetpoint[0] < SCPTsetpoint[1]

SCPToffset

nvoTSPVal

{SNVT_lev_percent}
{-163.840...163.835}
{0.0}

nvoTSPVal zero (offset) adjustment.
Added to the calculation result with SCPTsetpoint[0,1] and 
SCPTgain.

SCPTgain

nvoTSPVal

{SNVT_muldiv 
(mulplier,divisor)}
{0...32000,10000}
{10000,10000}

nvoTSPVal span (gain) adjustment.
Gain = Multiplier / 10000 (Divisor is fixed at 10000.)
Applied to SCPTsetpoint[0,1].

After adj.

(1°C added)

• nvoTSVal Offset Adjustment Example

• nvoTSVal Gain Adjustment Example

nvoTSVal outputs 26°C

with the input 25°C.

SCPToffset [0] = 25.0

SCPToffset [1] = 26.0

nvoTSVal outputs 25°C with the input 25°C.

nvoTSVal outputs 36°C instead of 35°C 

with the input 35°C.

SCPToffset [0] = 25.0

SCPToffset [1] = 25.0

SCPTdefScale = 110.0%

(36 – 25) / (35 – 25) = 1.1 = 110%

Before adj.

26

°C

25

25

°C

After adj.

Before Adj.

36
35

°C

25

25

35

°C

Summary of Contents for R7L-TS4




















Reviews: