background image

7.2.  CONNECTION DIAGRAM

SLD

FG

DG

DB

DA

T8

JACK

T7

T6

Comm.

Circuit

Note 1: This device is not designed to cancel noise included in the input signals.
             Be careful to eliminate such noise by using shielded cables.
Note 2: Be sure to maintain the same potential at all the common negative terminals for DC input.
Note 3: CC-Link version selector input is valid only at the moment of the power turned on.
             Firmware version 0B.00 or higher.  Use the R1X Configurator Software (model: R1CON)
             or consult M-System to confirm the firmware version.
Caution: FG1 terminal is NOT a protective conductor terminal.

 

 

 

9

8

7

6

5

4

3

2

1

10

12

11

13

15

14

16
17
18

20

19

21
22
23
24
25

27

26

28
29
30
31
32
33

35

34

36

T/C INPUT

+

DC INPUT

INPUT 1

INPUT 2

INPUT 3

INPUT 4

INPUT 5

INPUT 6

INPUT 7

INPUT 8

INPUT 9

INPUT 10

INPUT 11

INPUT 12

INPUT 13

INPUT 14

INPUT 15

INPUT 16

CJC

Sensor

+

ext. wire

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

Power

Circuit

Input

Circuit

To Other
CC-Link Devices

FG1

U (+)
V (–)

POWER

CONFIGURATOR

CC-Link VERSION SELECTOR INPUT

+

R1C-GH

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-5956  Rev.11  P. 7 / 13

Summary of Contents for R1C-GH














Reviews: