Lynx RaveTM 600 Operator'S Manual Download Page 81

Page: 81 / 134



WARNING

Before proceeding with any sus-
pension adjustment, remember:
– park in a safe place
– remove the tether cord cap

(DESS key).



WARNING

Always adjust both front springs to
same position.

FRONT SPRINGS ADJUSTMENT

HANDLING STEERING PROBLEM SOLUTION

Good

Comfortable No adjustment required

Bad

Too easy

to turn

Adjusted

too soft

Increase

spring

preload

Bad

Hard to turn

Adjusted

too hard

Decrease

spring

preload

Preload Adjustment

mmo2008-003-038_a

1. Adjustment ring
2. Ring positions

CAUTION:

Make sure that both

front springs are still pre loaded
when front of vehicle is off the
ground.

Front Suspension Shock
Damping

Rave 600 HO E-TEC and 800
R Power Tek Only

Compression/Rebound
Adjustment

Front shock on the above men-
tioned models feature a compression/
rebound adjustment.

Turn the damping adjuster accordingly.
Turning it clockwise increases shock
damping action (stiffer).

mmo2007-009-020_a

TYPICAL

1. Damping adjuster

_____________________

Summary of Contents for RaveTM 600







































































































































Search results

Summary of Contents for RaveTM 600

Reviews:

Related manuals for RaveTM 600

Brands by name

Popular brands

Lynx RaveTM 600, Operator'S Manual

Search results

Summary of Contents for RaveTM 600

Reviews:

Related manuals for RaveTM 600

Brands by name

Popular brands