background image

 

 
 
 

                              

Direct Vent Gas Fireplaces 

Model Riviera-66 

Luxor Manufacturing Mfg. 

#103-7075 Beatty Dr. Mission, B.C. Canada V2V-6C4 

Installation and Owner’s Manual 

 

 

 

 


.

 

 
 
 
 
 
                                                                                  
 
 
 
 
 

 

PLEASE NOTE

: This product has been manufactured using 

steel and screws.  As a result, there are many sharp edges 
that can easily cut exposed skin.  It is highly recommended 
that you wear proper protective gloves while installing the 
unit, and during routine cleaning or maintenance.

 

INSTALLER

:

 Leave this manual with the customer 

CUSTOMER: Retain this manual for

 

future reference

 

 

© 

 
 
 
 
 
 
--Do not store or use gasoline or other 
   Flammable vapors and liquids in the 
   vicinity of this or any other appliance. 
 
--WHAT TO DO IF YOU SMELL GAS 
 
•   Do not try to light any appliance 
•   Do not touch any electrical switch; do 
     Not use any phone in your building; 
•   Immediately call your gas supplier from a 
     neighbor’s phone. Follow the gas  
     supplier’s instructions. 
•   If you cannot reach your gas supplier, call 
     The fire department. 
 
-- Installation and service must be performed 
    By a qualified installer, service agency or 
    the gas supplier 
 

 
 

WARNING: If the information in these 
instructions is not followed exactly, a fire or  
explosion may result causing property damage, 
personal injury or death. 

 

 

Summary of Contents for Riviera-66



























Reviews: