Lutron Electronics EcoSystem Energi Savr Node, Installation Manual

Page: 5 / 12

EcoSystem
®
Energi Savr Node
TM
Installation Guide Lutron
®
|
5
EcoSystem
®
Energi Savr Node
TM
|
Installation Guide
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V MU
X
PWR
TEMP TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H N G
ECO2 ECO1
H N G
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V MU
X
PWR
TEMP TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H N G
ECO2 ECO1
H N G
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V MU
X
PWR
TEMP TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H N G
ECO2 ECO1
H N G
Step 4: Input group wiring
To connect a daylight sensor, occupant sensor, or infrared (IR) receiver, refer to the instruction sheets provided with the devices.
The diagram for the input terminals is shown below.
WARNING! Danger of Shock. May result in serious injury or death.
DO NOT WIRE WHEN LIVE! Switch off power to all power
feeds via circuit breaker or isolator before wiring or servicing the EcoSystem Energi Savr Node unit.
Buttons and LEDs in the unit are used for troubleshooting. If wiring is exposed when accessing buttons and LEDs, the unit
must be accessed by a certified electrician, following local codes.
Note: The EcoSystem Energi Savr Node unit accepts only one IR input (either daylight/IR sensor, IR receiver, or EcoSystem wallsta-
tion) per group.
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V MU
X
PWR
TEMP TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H N G
ECO2 ECO1
H N G
NOTE: There are four input groups. Each group has the
same inputs as shown in the diagram below.
Occupancy Sensor
EcoSystem
Wallstation*
Red Red
20V
Black Black
COM
Yellow Blue** Black Red White*
20 V – 20 V
Occ – Occupancy Sensor
Photo – Daylight Sensor
IR – IR Receiver*
Com – Common
Group 1 shown Group 2 shown
White*
IR
LUT
RON
Daylight/IR Sensor*
LUTR
O
N R
LUTR
O
N R
Note: Maximum wire run
length to each input not
to exceed 150 ft (46 m).
Input Group Wiring:
• 20 AWG to 12 AWG
(0.5 mm
2
to 4.0 mm
2
)
• Strip length: 1/4 in (6 mm)
• Torque: 5 in-lbs (0.5 N
•
m)
Input Group Wiring
IR Transmitter
IR Transmitter
* Note: Only one IR device may be connected per input. If the IR signal from a day-
light sensor is connected, a wall control may not be connected to the same input,
and vice-versa.
**
Connect the gray wire on -R model occupancy sensors.