EcoSystem
®
Energi Savr Node
TM
Installation Guide
Lutron
®
|
3
EcoSystem
®
Energi Savr Node
TM
|
Installation Guide
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V
MU
X
PWR
TEMP
TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE
ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H
N
G
Step-by-step installation instructions
Step 1: Mounting the
EcoSystem Energi Savr
Node
Unit
Note: Mount the
EcoSystem
Energi Savr Node
unit
in a posi-
tion where it can be easily located and accessed if service or
troubleshooting is necessary.
• For indoor use only!
• NEMA, Type 1 enclosure, IP20.
• Remove metal outer panel cover.
• Remove internal plastic line voltage shield.
• Choose panel mounting location so line voltage wiring is at least
6 ft (1.8 m) from audio or electronic equipment and associated
wiring (prevents radio frequency interference).
• Install in accordance with all national and local electrical codes.
Mechanical Dimensions
All dimensions shown as inches (mm)
Control Power Wiring
11.25
(285.75)
10.25
(260.35)
0.20
(5.16) dia.
1.00
(25.40)
1.5
(38.10)
1.22
(30.99)
1.66
(42.16)
1.31
(33.27)
0.88
(22.35)
1.22
(30.99)
1.62
(41.15)
9.25
(234.95)
7.50
(190.50)
3.16
(80.26)
13.25
(336.55)
Step 2: Control power wiring
The
EcoSystem
Energi Savr Node
unit
operates at 120-277 V .
Use the following instructions to wire line voltage to the
EcoSys-
tem
Energi Savr Node
unit.
WARNING! Danger of Shock. May result in serious
injury or death.
DO NOT WIRE WHEN LIVE! Switch off
power to all power feeds via circuit breaker or isolator
before wiring or servicing the
EcoSystem
Energi Savr
Node
unit.
Buttons and LEDs in the unit are used for troubleshooting.
If wiring is exposed when accessing buttons and LEDs, the
unit must be accessed by a certified electrician, following
local codes.
1. Turn power off.
2. Remove metal outer panel cover.
3. Remove internal plastic line voltage shield.
4. Use 14 AWG to 12 AWG (2.5 mm
2
to 4.0 mm
2
) conductors (de-
pending on breaker rating) to feed the control power wiring. The
device draws less than 0.5 A.
5. Wire the line voltage cables to the terminals labeled H (Hot), N
(Neutral) and G (Ground).
6. Reinstall internal plastic line voltage shield.
7. Turn on the circuit breaker or isolator to power up the
EcoSys-
tem
Energi Savr Node
unit. The Power LED on the
EcoSystem
Energi Savr Node
unit will illuminate continuously when prop-
erly energized. If the LED does not light, turn off power, then
check the control power wiring.
8. Turn power off.
Control Power Wiring:
• Two (2) 14 AWG to 12 AWG
(2.5 mm
2
to 4.0 mm
2
)
• Strip length: 3/8 in (8.5 mm)
• Torque: 7 in-lbs (0.79 N
•
m)
Hot (H)
Neutral (N)
Ground (G)
Do not use
QS LINK
ECO1
ECO1
RESET
ECO2
TEST
GROUP 1
+20V
OCC
1
PHO
TO
1
IR
1
CO
M
+24V
MU
X
PWR
TEMP
TEST
MU
X
CO
M
GROUP 2
+20V
OCC
2
PHO
TO
2
IR
2
CO
M
GROUP 3
+20V
OCC
3
PHO
TO
3
IR
3
CO
M
GROUP 4
+20V
OCC
4
PHO
TO
4
IR
4
CO
M
CONTACT CLOSURE
ETHERNET
CC
I
CO
M
EMER
G
CO
M
ECO1
H
N
G
Line Voltage Shield
