Section 13
–
Direct Commands
Copyright 2007-2017 Lumagen, Inc Radiance Pro, Rev 071719
42
Section 13
–
Radiance Pro Direct Commands
Direct Commands can be used for initial configuration or for settings not in the menu. Direct Commands are
entered using the Lumagen remote control or RS232 interface. Make sure to do a Save after changes.
Miscellaneous Direct Commands
MENU 0727
Erase Configuration Memory: In Service Mode enter command, answer question, remove
power. More aggressive than Factory Reset. No Save needed. Cannot be undone.
MENU 0811
Set current input to report HDCP 1.X back to sources
MENU 0819
Set all inputs/memories to report HDCP 1.X back to sources
MENU 0821
Set current input to report HDCP 2.2 back to sources
MENU 0827
Set output aspect to 2.35 (no Anamorphic-lens). This command implements all steps of
the “Fixed 2.35 Output Aspect” section of Tech Tip 16
MENU 0829
Set all inputs/memories to report HDCP 2.2 back to sources
MENU 0850
Load original 18 GHz output microcode. Unit flashes output microcode and reboots
MENU 0851
Load new 18 GHz output microcode. Unit flashes output microcode and reboots
MENU 0860
Globally turn Darbee processing off
MENU 0861
Globally turn Darbee processing on
MENU 0870
Set default Auto output mode. This clears manual output overrides
MENU 0871
Set output as 4k24, 4k25, 1080p50, 1080p60 based on input rate
MENU 0872
Set output as 4k24, 4k25, 4k50, 4k60 based on input rate, with rate match off
MENU 0873
Set output as 4k50/4k59.94, 9 GHz max, based on input rate, with rate match off
MENU 0874
Set output as 4k50/4k59.94, 18 GHz max, based on input rate, with rate match off
MENU 0875
Set HDMI output format as 4:2:2 on all styles (as appropriate)
MENU 0876
Set output as 2048x1080 at 24, 50, 60 Hertz with rate match off
MENU 0877
Set output as 4096x2160 at 24, 50, 60 Hertz with rate match off
MENU 0910
Temporary Service Mode (see
Other->Menu Mode
which has Permanent Service Mode)
MENU 0927
Disable/Enable
the “Show Info Page on RS232 <cr>”
(carriage return) character
MENU 0940
Reinterlacing off
MENU 0941
Reinterlacing on. Reinterlacing only available for 480p and 576p source modes.
MENU 0943
Report all HDMI audio modes in EDID back to sources (feature toggle)
MENU 0944
Report basic HDMI audio modes (2-Ch PCM and DD 5.1) back to sources (feature toggle)
MENU 0966
Globally set Letter Box Zoom on or off
MENU 0995
Disable IR commands. Repeat to re-enable IR commands (this is the only IR command
accepted when IR commands are disabled). IR disable mode cannot be Saved
MENU 0999
Load Factory Settings (temporary Factory Reset unless Saved)
ALT PREV
Restart the Radiance Pro outputs. Use if TV/Projector has trouble locking on the signal
Output Resolution Direct Commands
The following output mode commands are intended for temporary testing only and affect only the current
input, input memory and input resolution. These revert to Saved setting if a new input is selected and are
not saved. Use the
Output Setup
Menu to program the output mode, or modes, if the “Auto” setting is not
being used (or use MENU 0871 or MENU 0872 above).
480p:
MENU 021
Progressive with 480 active scanlines
720p:
MENU 024
Progressive with 720 active scanlines
1080i:
MENU 028
Interlaced with 1080 active scanlines
1080p24:
MENU 020
Progressive with 1080 active scanlines
1080p:
MENU 027
Progressive with 1080 active scanlines
4k24:
MENU 023
Progressive with 2160 active scanlines
4k50:
MENU 025
Progressive with 2160 active scanlines
4k60:
MENU 029
Progressive with 2160 active scanlines
