LUDLUM 3030 Manual Download Page 21

Page: 21 / 79

Model 3030 & 3030E Series

Technical Manual

Section 4

Ludlum Measurements, Inc.

Page 9

November 2017

ALPHA

: A six-digit backlit LCD readout indicates counts received in the

alpha counting channel.

BETA

: A six-digit, backlit LCD readout indicates counts received in the beta

counting channel.

: A red LED indicator illuminates whenever QC is needed. When a valid

QC check is performed, the QC indicator turns off. Additionally, the QC

indicator is turned off when the QC check feature is disabled (during setup).

: A red LED indicator illuminates whenever the internal circuitry detects a

current overload to the detector. This warning usually indicates an open
sample tray or a torn window on the front of the internal detector.

Instrument will not count while this indicator is illuminated.

CPM

: A green LED indicator illuminates whenever CPM mode is

established (during setup).

DPM

: A green LED indicator illuminates whenever DPM mode is

established (during setup).

αAL

: A red LED indicator illuminates whenever the alpha count exceeds the

alarm level established during setup.

βAL

: A red LED indicator illuminates whenever the beta count exceeds the

alarm level established during setup.

Back Panel

Detector Input Connection

(Model 3030E only): a series "C" coaxial

connector; other connectors are available upon request

RS-232

: a 9-pin D-connector for connection to printer or computer

CAL

: a cover for the calibration potentiometers, which should only be

adjusted by trained and authorized personnel during calibration

INPUT

: line or mains power receptacle and fuse holder. Use of two

one-amp, fast-blowing fuses provides protection to the instrument in case of

internal electrical failure.

Remove the calibration (cal) cover plate to access the following
calibration potentiometers:

A-TH

: a multi-turn potentiometer used to vary the alpha pulse discriminator

from 40 to 700 mV, normally set at 120 mV

Summary of Contents for 3030
















































































Search results

Summary of Contents for 3030

Reviews:

Related manuals for 3030

Brands by name

Popular brands

LUDLUM 3030, Manual

Search results

Summary of Contents for 3030

Reviews:

Related manuals for 3030

Brands by name

Popular brands