LUDLUM 3030 Manual Download Page 25

Page: 25 / 79

Model 3030 & 3030E Series

Technical Manual

Section 5

Ludlum Measurements, Inc.

Page 13

November 2017

Warning!

The operator is strongly cautioned to take the following

precautions to avoid contact with internal hazardous live parts
that are accessible using a tool:
1. Turn the instrument power

OFF

and disconnect the power

cord.
2. Allow the instrument to sit for one minute before accessing
internal components.

CAUTION, RISK OF ELECTRIC SHOCK

(per ISO 3864, No. B.3.6)

– designates a terminal (connector) that allows connection to a voltage
exceeding one kV. Contact with the subject connector while the instrument

is on or shortly after turning off may result in electric shock. This symbol
appears on the rear panel of the Model 3030E only.

The “

crossed-out wheelie bin

” symbol notifies the consumer that the

product is not to be mixed with unsorted municipal waste when discarding;

each material must be separated. The symbol is placed near the AC
receptacle. See section 8, “Recycling,” for further information.

Replacement of Main Fuse (Back Panel)

Warning!

For continued protection against risk of fire, replace only with

fuse of the specified type and current rating!

Summary of Contents for 3030
















































































Search results

Summary of Contents for 3030

Reviews:

Related manuals for 3030

Brands by name

Popular brands

LUDLUM 3030, Manual

Search results

Summary of Contents for 3030

Reviews:

Related manuals for 3030

Brands by name

Popular brands