manualshive.com logo in svg

LRS LineShare PRO, Operator'S Manual, Page: 37 / 43

Share
Download
LRS LineShare PRO Operator'S Manual Download Page 37

Single Tone Detection Timer

This feature designates the timing parameters for operation of the Single Tone Detection feature.

When Single Tone Detection is activated, but this timer expires on a call, the LineShare Pro 104 will not trans-
fer calls producing identifying tones.

This feature has a range of 4-30 seconds.

The factory setting for the Single Tone Detection Timer is 10 seconds.  To change this feature, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 52 _ _ *  (three beeps) * (one beep) (Blank spaces represent new Single Tone

Detection Timer setting)

3. Hang up the phone

Remote Security Access Code – Remote Programming

Operates only in the Automatic mode.

This feature assigns the access code that is required to enter the programming mode of the LineShare Pro
104 from a remote location.

Once entered, the LineShare Pro 104 stores it in non-volatile memory until removed through programming.
It is not changed when factory settings are restore.

The Remote Security Access Code can be 1to 4 digits not including the # key.  See Pound Key Transfer Re-
quired for use with the Remote Security Access Code.  Do not use a transfer code for a port on the LineShare
Pro 104, or 0 0 0 0 as it will disable remote programming.

The factory setting for the Remote Security Access Code is unprogrammed for your protection. It must be
entered before you can access the remote programming mode.  

To enter an access code, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 6 0 _ _ _ _ *  (three beeps) * (one beep)  (blank spaces represent the new

Remote Security Access Code)

3. Hang up the phone

To disable remote programming, perform the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 6 0 0 0 0 0 *  (three beeps) * (one beep)  

3. Hang up the phone

Port P1 Transfer Code

This feature assigns the access code to transfer a call to port P1.

The Port P1 Transfer Code can be 1 to 4 digits not including the # key. See Pound Key Transfer Required for
use with the Port P1 Transfer Code.  Do not use a code that is a transfer code for another port on the Line-
Share Pro 104.

The factory setting for the Port P1 Transfer Code is 1 1. 

Long Range Systems

36

Line Share PRO

Summary of Contents for LineShare PRO












































Reviews:

No comments