LRS LineShare PRO Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 43

LRS LineShare PRO Operator'S Manual Download Page 21

Programming the LineShare Pro 104

Introduction

The LineShare Pro 104 has many programmable features and settings that can be used to customize its op-
eration for your specific application.

Many of these features have either feature settings and/or timing parameters associated directly with their
operation. Therefore, please read the following sections carefully to obtain the best results when program-
ming the LineShare Pro 104.

Programming Locally

Connect the LineShare Pro 104 as shown, using a tone phone connected to P2.

NOTE:

Programming changes can only be made through port P2.

Programming changes can only be performed from a tone phone connected to port P2 of an operational
unit. The LineShare Pro 104 will not process calls during programming sessions.

Entering the Programming Mode

Method 1 – DTMF Dialing

To enter the programming mode, take the phone off-hook, press # * . You will hear three beeps indicating
the unit is in the programming mode.

Once in programming, the LineShare Pro 104 allows 8 seconds between tone commands before exiting the
programming mode without saving the changes. Therefore, it would be beneficial to write down all pro-
gramming changes before entering the programming mode.

Once a complete programming command is entered, it must be followed by the * key, which stores it into
memory. After you enter the * key, you can set as many additional features or feature settings as needed for
your application. When all programming changes are completed, press * * to save the changes in non-
volatile memory and exit the programming mode. There is one final beep when exiting programming mode
before returning to a dial tone.

Method 2 - Power-up Programming Mode

If during a programming session using method 1 above, you receive a dial tone, the intercept operator mes-
sage, or if programming was not successful, the LineShare Pro 104 incorporates another method to enter the
programming mode. This method is available anytime the LineShare Pro is powered ON. To use this method

Long Range Systems

20

Line Share PRO

«
...
19
20
21
22
23
...
»

Summary of Contents for LineShare PRO












































Reviews:

No comments