manualshive.com logo in svg

LRS LineShare PRO, Operator'S Manual, Page: 12 / 43

Share
Download
LRS LineShare PRO Operator'S Manual Download Page 12

Long Range Systems

11

LineShare PRO1

Operating Modes

Automatic Mode

NOTE: 

The access codes and routing tones can be changed through programming.

The LineShare Pro 104 will ring the Primary port up to 6 times (Rings to port P1 in this example).  If the call
remains unanswered after 6 rings, the LineShare Pro 104 transfers (Automatic No Answer Transfer) the call
to the Secondary port. The Automatic No Answer Transfer feature accommodates fax machines that do not
produce a CNG tone, and can be turned off through programming.

If a device connected to the Primary port answers a call, the LineShare Pro 104 will disable the Single Tone
Detection feature. Then, only DTMF (tone) transfers using access codes are allowed as follows:

port P1   # 

1 1

tone

port P2   # 

2 2

tone

port P3   # 

3 3

tone

port P4   # 

4 4

tone

The above access codes are the factory settings and may be changed by the user.

Any time a call is transferred to another port, the port that is off-hook with the call is the only port that will
be allowed to transfer the call. The originating port will receive a busy tone once the transfer occurs.

To accommodate faxes that do not produce CNG tones, the Automatic Primary Port Transfer feature can
transfer a call to another port (Secondary Port Selection) when using an answering machine with the Line-
Share Pro 104. The factory setting for this feature is OFF, and uses the Primary Port Transfer Timer to set pa-
rameters for transfer as described later in this guide.

The factory setting for the LineShare Pro 104 is the Automatic mode. To change the operating mode, see
"Programmable features of the LineShare Pro 104" for more information.

NOTE:

In the Automatic mode, any phone(s) not connected to an LINESHARE PRO port will only ring
1 time (Rings to Answer Call) on inbound calls and do not have complete access to the phone
line unless Extension Detection is turned ON.

Summary of Contents for LineShare PRO












































Reviews:

No comments