manualshive.com logo in svg

LRS LineShare PRO, Operator'S Manual, Page: 32 / 43

Share
Download
LRS LineShare PRO Operator'S Manual Download Page 32

Emergency Call Override Action – Priority Outbound Call

This feature permits the Emergency Call Override feature to operate the phone company’s 3-way calling serv-
ice.

Please refer to the Emergency Call Override section for operating procedures with the LineShare Pro 104.  

The factory setting for Emergency Call Override is set to go on-hook for 2.2 seconds  [# * (three beeps) 0 1 5
*  (three beeps) * (one beep) ]

To set the LineShare Pro 104 for operation with the 3-way calling feature (LineShare Pro 104 performs a flash), use the
following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 1 5 *  (three beeps) * (one beep) 

3. Hang up the phone

To set the LineShare Pro 104 to go on-hook for 2.2 seconds, use the following steps:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 0 1 5 *  (three beeps) * (one beep) 

3. Hang up the phone

Caller ID Retransmission

This feature allows Caller ID devices to be connected to any port of the LineShare Pro 104 and  requires Caller
ID service activation from the phone company.

Operation in the Automatic mode and Semi-Automatic mode vary as follows:

Automatic Mode

When the LineShare Pro 104 is in the Automatic mode, the unit detects the incoming ring signal and receives
the caller ID information between the first and seconds rings.  Before the second ring, the LineShare Pro 104
answers and processes the call normally.  The determined port is rung and the Caller ID information is re-
transmitted to the port after the first ring to the port.  The Caller ID information is only retransmitted only time.
It is not retransmitted if the call is transferred from one port to another.  If Distinctive Ring Service Detection
is turned ON, only the port designated by the DRS Assignment will receive the Caller ID information.

Semi-Automatic Mode

When a call comes in, the first ring of a call passes directly to the Primary port. Between the first and second
rings, the Caller ID will display its information, and the call is then processed normally.  NOTE: If Distinctive
Ring Service Detection is turned ON, the second ring will be processed as described in "Distinctive Ring Serv-
ice." Only the port designated by the DRS Assignment will receive the Caller ID information.

The factory setting for Caller ID Retransmission is ON.  Caller ID Pass Thru must be OFF before this feature
is turned ON.

To turn this feature ON:

1. Take the phone in port P2 off-hook

2. Press # * (three beeps) 1 1 8 *  (three beeps) * (one beep) 

3. Hang up the phone

Long Range Systems

31

Line Share PRO

Summary of Contents for LineShare PRO












































Reviews:

No comments