Stove ON 13:45
Burner start-up
Output <||
||
|
||
||
|
||
||
|
||
||
|
||
||
|
||
||
|
---->
Stove ON 13:45
Burner ON
Output <||
||
|
||
||
|
||
||
|
||
||
|
||
||
|
||
||
|
---->
page 18
General note – Surfaces
Only high-quality air-drying varnish is used which does not smell nor give off
fumes when heated up for the first time if it is allowed to dry completely (at
room temperature). If the appliance is heated up shortly before the varnish has
hardened, an unpleasant smell and fume will be temporarily produced. Please
give the room where the appliance is located a good airing.
Charging the storage container
Make sure that you use approved pellets which conform to ÖNORM M7135/DIN
51731 – see imprint on the pellets bags or consult your pellets supplier. Open
the container lid. To avoid raising of dust, pour pellets slowly and not from too
high a position. After feeding the pellets, the lid is to be closed and should
remain closed during operation.
20. Operating the stove for the first time
20. Operating the stove for the first time
•
Do not leave small children unattended in the vicinity of the stove: the
heating system is not childproof!
•
Prior to the first start-up all connections (chimney flue connection, power
supply, etc.) are to be checked.
•
The viewing glass as well as the door become very hot when the stove is in
use (temperatures up to 300 °C). Pay attention to the fact that these parts
must not be touched when the stove is in operation.
•
Keep the firebox door closed at all times, even if the stove is not in use.
•
Make sure that no objects are in the combustion chamber, in the firebox as
well as in the oven.
•
Only after the installation is completed in accordance with the user manual
and installation instructions, is it allowed to charge the storage container
with pellets (at least 5 kg).
•
Do not leave small children unattended in the vicinity of the stove: the
heating system is not childproof!
•
Prior to the first start-up all connections (chimney flue connection, power
supply, etc.) are to be checked.
•
The viewing glass as well as the door become very hot when the stove is in
use (temperatures up to 300 °C). Pay attention to the fact that these parts
must not be touched when the stove is in operation.
•
Keep the firebox door closed at all times, even if the stove is not in use.
•
Make sure that no objects are in the combustion chamber, in the firebox as
well as in the oven.
•
Only after the installation is completed in accordance with the user manual
and installation instructions, is it allowed to charge the storage container
with pellets (at least 5 kg).
The regulation is determined by the specified boiler set-point temperature
(75°C or 65°C respectively, see setting
SUMMER /WINTER
).
Should the boiler set-point temperature be exceeded by 10°C, the appliance
shuts down automatically
display burner OFF and switches on again once the
boiler set-point temperature has fallen below the value by 3 °C.
21. Heating operation with pellets
21. Heating operation with pellets
•
While the appliance operates on pellets, the damper (start-up flap) (see
instruction manual stove) must not be opened!
•
Set both stove air regulators to level “0”!
•
While the appliance operates on pellets, the damper (start-up flap) (see
instruction manual stove) must not be opened!
•
Set both stove air regulators to level “0”!
The appliance might resume operation automatically at any time, therefore please
note the information in point External Release /Remote control unit!
The appliance might resume operation automatically at any time, therefore please
note the information in point External Release /Remote control unit!
Switching the appliance on
Press the button
once in the top level of the menu.
The display
StOve ON
appears as well as the operating status burner start-up
(figure 56).
The appliance switches on.
Setting the heating output
Setting of the heating output in the top level of the menu (figure 57).
Reduce heating output by pressing the button
.
Increase heating output by pressing the button
.
Adjustment range heating output:
3 - 10 for air heaters (P6)
5 - 10 for central heating appliances (P7, type designation -Z)
If the heating output is not sufficient although it has been set at the highest
level, the temperature can be increased by loading firewood.
fig. 57
fig. 58