background image

12 

Troubleshooting – Across-the-rails infrared sensing 

[This section still needs to be written!!!] 

 

Warranty 

This product is warranted to be free from defects in materials or workmanship for a period of one year from the date of purchase.

  

Logic Rail Technologies

 reserves the right to repair or replace a defective product.  The product must be returned to

 Logic Rail 

Technologies

  in  satisfactory  condition.    This  warranty  covers  all  defects  incurred  during  normal  use  of  this  product.    This 

warranty is void under the following conditions: 
 

1) If damage to the product results from mishandling or abuse. 

 

2) If the product has been altered in any way (e.g. soldering to the circuit board). 

 

3) If the current or voltage limitations of the product have been exceeded. 

Requests for warranty service must include a dated proof of purchase, a written description of the problem, and return shipping 
and  handling  ($8.00  inside  U.S./$20.00  outside  U.S.  -  U.S.  funds  only).    Except  as  written  above,  no  other  warranty  or 
guarantee, either expressed or implied by any other person, firm or corporation, applies to this product. 
 

Technical Support 

We  hope  the  preceding  instructions  sufficiently  answer  any  questions  you  might  have  about  the  installation  of  this  product. 
However, technical support is available should you need it. You can reach us via phone or email; our contact information can be 
found on the top of page 1.  

Summary of Contents for GCP/2













Reviews: