background image

48

8  

Gas connections

Connecting gas supply piping

1.  Remove the top access panel and refer to FIG.’s 8-1 thru 

8-2 to pipe gas to the boiler.

  a.  Install ground joint union for servicing, when  

  

required.   

  b.  Install a manual shutoff valve in the gas supply  

  

piping outside boiler jacket when required by local  

  

codes or utility requirements.

  c.  In Canada – When using manual main shutoff  

  

valves, it must be identified by the installer.

2.  Install sediment trap / drip leg.

Figure 8-1 

Gas Supply Piping - Models 400 - 500

3.  Support piping with hangers, not by the boiler or its 

accessories.

Do not check for gas leaks with an open 

flame – use the bubble test.  Failure to use 

the bubble test or check for gas leaks can 

cause severe personal injury, death, or 

substantial property damage.

Figure 8-2 

Gas Supply Piping - Models 650 - 1000

4.  Purge all air from the gas supply piping.

5.  Before placing the boiler in operation, check the boiler 

and its gas connection for leaks.

 

a.  The appliance must be disconnected from the gas  

  

supply piping system during any pressure testing of  

  

that system at a test pressure in excess of 1/2 PSIG  

  

(3.5  kPa).

 

b.  The appliance must be isolated from the gas supply  

    piping system by closing a manual shutoff valve  

 

 

during any pressure testing of the gas supply piping  

 

 

system at test pressures equal to or less than 1/2 PSIG  

  (3.5 

kPa).

 

c.  The appliance and its gas connection must be leak  

 

 

tested before placing it in operation.

The gas valve and blower will not support 

the weight of the piping.  Do not attempt 

to support the weight of the piping with 

the boiler or its accessories.  Failure to 

comply could result in severe personal 

injury, death, or substantial property 

damage.

 WARNING

 WARNING

6.  Use pipe sealing compound compatible with propane 

gases.  Apply sparingly only to male threads of the pipe 

joints so that pipe dope does not block gas flow.

DIR #2000585192   00

UNION

(FIELD PROVIDED)

SEDIMENT TRAP / 

DRIP LEG

GAS SUPPLY

MANUAL SHUTOFF VALVE 

(FACTORY SUPPLIED)

DIR #2000585192   00

UNION

(FIELD PROVIDED)

SEDIMENT TRAP / 

DRIP LEG

GAS SUPPLY

MANUAL SHUTOFF VALVE 

(FACTORY SUPPLIED)

     

Installation & Operation Manual

Summary of Contents for Knight XL 100 Series

















































































Reviews: