Lochinvar EcoSword LGC 160-210 G P CE Installation, Commissioning, User & Maintenance Instructions Download Page 40 | Manualshive

Page: 40 / 94

background image

Installation
type

Version

Description

C43

Closed

Water heaters on common air inlet and flue gas
outlet (concentric and/or parallel) in a multiple
floor building.

C53

Closed

Separate air inlet and flue gas outlet terminal
types mixed. Air inlet and flue gas outlet
termination may be in different pressure zone.

C63

Closed

Water heaters supplied without venting materials.
These water heaters must be installed in
compliance with local regulations. The water heater
is intended to be connected to a separately
approved and marketed venting system.

This manual does not discus installation type B23. When you need a B23 system, contact
Lochinvar for more information.

Caution
Always make sure that the venting system is mounted into an area suitable for the
correct type of installation.

Caution
The use of a different wall or roof terminal can result in incorrect functioning of the water
heater. Use the part number from the table to order a terminal set from your supplier or
the manufacturer.

c

40

Installation, Maintenance and Service part

«
...
38
39
40
41
42
...
»

Summary of Contents for EcoSword LGC 160-210 G P CE































































































Reviews:

No comments

Related manuals for EcoSword LGC 160-210 G P CE

FCD-JTHMG80-III

Brand: Haier Pages: 2

Little Sea-ox FCD-JTHC40-III (E)

Brand: Haier Pages: 6

Brand: Haier Pages: 18

Brand: Haier Pages: 23

Brand: Haier Pages: 20

Brand: Haier Pages: 2

Brand: Zilmet Pages: 10

Brand: Eccotemp Pages: 90

Brand: Eccotemp Pages: 40

Brand: Eccotemp Pages: 19

Brand: DAYLIFF Pages: 12

STELLAR BLACK PH7056

Brand: Gasmate Pages: 8

Brand: Jata calor Pages: 24

Brand: U-Line Pages: 3

Brand: Annovi Reverberi Pages: 18

COBRA DS 0600 E

Brand: BUSCH Pages: 24

MULTIMAXX HG 24

Brand: FläktGroup Pages: 63

Brand: K Tool International Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands