Lochinvar EcoSword LGC 160-210 G P CE Installation, Commissioning, User & Maintenance Instructions Download Page 3

Page: 3 / 94

Preface

Copyright

Nothing from this publication may be copied, reproduced and/or published by means of
printing, photocopying or by whatsoever means, without the prior written approval of
Lochinvar Ltd..

Lochinvar Ltd. reserves the right to modify specifications in this manual.

Trademarks

Brand names in this manual are registered trademarks of their respective owners.

Warranty

Refer to the appendix Warranty (see 13.6) for the warranty provisions.

Liability

User

Lochinvar accepts no liability when the water heater is not used correctly and requires the
user to:

•

Read this manual carefully and obey the instructions.

•

Ask your installation engineer for advise about the use of the water heater.

•

Make sure that the service and maintenance activities are done by a qualified
engineer.

•

Store the manual, in good condition, near the water heater.

Installation engineer

Lochinvar accepts no liability when the water heater is not used correctly and requires the
installation engineer to:

•

Read this manual carefully and obey the instructions.

•

Make sure that the entire water heater installation complies with the applicable
regulations (on page 4).

•

Make sure that the water heater is tested before the installation is taken into use.

•

Explain the correct use to the user.

•

Notify the user when service and maintenance activities are necessary.

•

Make sure that you hand over all applicable manuals.

0312582_EcoSword_V4.0, 03-05-2021

Summary of Contents for EcoSword LGC 160-210 G P CE































































































Search results

Summary of Contents for EcoSword LGC 160-210 G P CE

Reviews:

Related manuals for EcoSword LGC 160-210 G P CE

Brands by name

Popular brands

Lochinvar EcoSword LGC 160-210 G P CE, Installation, Commissioning, User & Maintenance Instructions

Search results

Summary of Contents for EcoSword LGC 160-210 G P CE

Reviews:

Related manuals for EcoSword LGC 160-210 G P CE

Brands by name

Popular brands