background image

10

Instruction Manual

SECTION 5 - CONTROL MODE SELECTION MENU

5.2  PULSE MULTIPLY MODE (EXTERNAL)

This mode is used to control the pump with an 
external device connected to the appropriate 
contacts  of  the  5-Pin  connector.  With  the  pump 
OFF, use the   UP and   DOWN buttons to vary 
the strokes-per-pulse parameter. To turn the pump 
ON or OFF, push the   POWER button, or toggle 
the remote ON/OFF. The   Pump ON/OFF LED 
will illuminate yellow when the pump is ON. With 
the pump turned  ON, and a pulse is received, the 
pump will begin running, with the remaining pulses 
counting down on the display.
If  a  pulse  is  received  before  the  countdown  is 
complete and Batch Mode is OFF (

see Sec. 6.2

), 

the    error  code  (

see Sec. 4.5

)  is  displayed 

and  the  pump  batch  count  then  restarts  from 
the  strokes-per-pulse  setpoint. The  fault  will  be 
corrected when the pump completes the current 
batch OR the pump is stopped.
If  a  pulse  is  received  before  the  countdown  is 
complete and Batch Mode is ON (

see Sec. 6.2

), the 

pump will accumulate strokes (up to a maximum 
of 9999), allowing all strokes to be accounted for.

Display Overview:

Icon/Alarm Area

Strokes per Pulse

Strokes Remaining

Stroke Length

Stroke Rate

Calculated Volume 

per Pulse

Calculated Volume

Injected

Pulse Multiply Mode 

(Pump OFF)

Pulse Multiply Mode 

(Processing Pulse)

1.

 

Icon/Alarm Area:

 The   icon indicates the 

pump is in the pulse multiply mode. Depending 
on advanced pump configuration options and 
any alarms/alerts detected, other icons may be 
present as well (

see Sec. 4.5

).

2.

 

Stroke Length:

 The numeric stroke length 

value  indicates  the  current  stroke  length  setting           
(in percent).

3.

 

Stroke Rate:

 Indicates the stroke speed of the 

pump (1-59 SPH or 1-120 SPM). To allow true 
flow proportioning, this is set in manual mode 
(

see Sec. 5.1

).

4.

 

Strokes per Pulse (Pump OFF only):

 Number 

of strokes (1-9999) to occur for each valid pulse 
input. 

See Sec. 6.3

 to define a valid pulse.

5.

 

Strokes Remaining (Pump ON only):

 Number 

of  strokes  remaining  for  the  current  batch 
cycle.

6.

 

Calculated Volume per Pulse (Pump OFF 

only): 

The  calculated  flow  based  on  stroke 

count,  stroke  length,  and  calibration  settings 
(

see Sec. 6.6 for calibration information

).

7.

 

Calculated Volume Injected (Pump ON only):

 

The  calculated  flow  based  on  strokes  made, 
stroke length, and calibration settings (

see Sec. 

6.6 for calibration information

).

NOTE: 

The pump will ignore the pulse input while the 

pump is OFF.
Depressing the   UP and   DOWN buttons 

simultaneously will cycle through alternate 

display formats , as shown below:

Summary of Contents for ROYTRONIC EXCEL AD9 series

































Reviews: