manualshive.com logo in svg

LIW BAFFIN Automatic, Manual, Page: 9 / 23

Share
Download
LIW BAFFIN Automatic Manual Download Page 9

9 

 

 

 

NOTE:  
Adjustments  should  be  carried  out  with  the  device  in  the  full  sitting  position.  After  adjustments  are 
made, make sure that all the adjusting screws are tightened. Failure to tighten them may be hazardous 
to the patient and may damage the device. Once the depth adjustment is done, adjust the seat position 
(see section 4.1.4)  

 

 

4.1.4

 

Adjusting the seat position  

Seat position is adjusted by sliding the right and left seat supports back or forward (fig. 5). The adjustment should be carried 
out with the device in a recumbent position, after loosening all six screws (three per each support). A properly adjusted seat 
will have a space of approx. 1 cm between the seat supports (left and right) and the bottom of the backrest when the device 
is in a recumbent position.  
In order to make the adjustment, remove the cushions from the seat and loosen all six screws securing the left and right seat 
supports (three per each support) (fig. 5). Put the device in a recumbent position and slide the seat supports back or forward, 
so there is a space of approx. 1 cm between the supports and the bottom of the backrest. After the adjustment is completed, 
tighten all six screws.  

 

 

Fig. 5 

Adjusting the seat position

 

 

NOTE:  
The adjustment should be done with the device in a recumbent position after loosening all securing 
screws. After each depth adjustment, make sure none of the seat supports collide with the backrest.  

 
 

4.2

 

 Adjusting the width and height of arm/side supports  

The width and height of arm supports are adjusted using the knobs marked with a red arrow (fig. 6). Left and right armpit 
supports  are  adjusted  independently.  The  knobs  are  located  on  both  sides  of  the  unit  and  operate  independently  of  each 
other, making it possible to set the supports symmetrically and asymmetrically with respect to the axis of the body.  
To adjust the height and width of the arm support, loosen the adjustment knob (fig. 6), set the armpit support in the desired 
position and tighten the adjustment knob. Perform an analogous regulation on the opposite side.  

 

Summary of Contents for BAFFIN Automatic
























Reviews:

No comments