manualshive.com logo in svg

LIW BAFFIN Automatic, Manual, Page: 12 / 23

Share
Download
LIW BAFFIN Automatic Manual Download Page 12

12 

 

 

 

The forward and backward adjustment of the kneepads is done by setting the pad at a desired depth. In order to adjust it, 

pull  back  the  pin  securing  the  kneepad  (fig.  10),  set  the  kneepad  to  a  desired  depth  and  release  the  pin.  After  the  pin  is 

released, make sure that the pin is safely located in the hole in the kneepad support.  

 

 

 

Fig. 10 

Adjusting the kneepads 

 

NOTE:   
The kneepad is used to support the leg while standing only. Do not use the kneepad while moving from 
sitting  to  lying  position.  Do  not  change  the  position  from  lying  to  sitting  (or  vice  versa)  with  the 
kneepad in place. The device has electrical interlocking, when the kneepad is in place actuator in back 
support is blocked. That means that the device will not move from sitting to lying position. Each time 
you  install  the  kneepad,  make  sure  it  is  secured  in  place  by  pulling  it  in  the  direction  of  the  support 
unlocking.  

 

4.5

 

Modelling (fitting) the backrest  

The BAFFIN devices feature a globally unique backrest modelled after a human spine. This construction allows for setting the 
user's back in an anatomical or corrective position.  

In order to adjust the backrest, loosen the adjustment screw (fig. 11), set the desired shape of the backrest and tighten the 

adjusting screw. After tightening the screw, the backrest will be fixed in place.  

 

Fig. 11 Modelling (fitting) the backrest 

NOTE:  
Rehabilitation  using  Multifunctional  device  can  not  start  without  prior  consultation  with  a  doctor 
taking  care  of  the  patient.  The  shape  of  the  backrest  can  only  be  adjusted  according  to  the    
recommendation from a doctor or physical therapist. 

 

Summary of Contents for BAFFIN Automatic
























Reviews:

No comments