LiteOn EVO6000 Series Quick Start Manual Download Page 64

Page: 64 / 102

Parameter

Name

Description

Setting Range

o4: Maintenance Settings

o4-00

Cumulative
Operation
Time Setting

Sets the initial value by 1 hours to start keeping
track of cumulative operation time.

Default: 0 h
Min.: 0
Max.: 9999

o4-06

U2 Reset Setting

Resets the data for U2-□□ (Fault Information) as
these data will not be reset by A1-03 (Reset).
0

∶

Disabled

∶

Enabled

Default: 0
Range: 0, 1

Group t, Auto-Tuning

t1: IM Motor Auto-Tuning

t1-01

Auto-Tuning Method
Selection

∶

Rotational Auto-Tuning

∶

Stationary Auto-Tuning

Default

∶

Range: 0, 1

t1-02

Motor Output
Power

Sets the motor rated output power in kW units.
Note: 1HP (Horse Power) = 0.746kW

Default

∶

Determined

by o2-03
Min.: 0.00 kW
Max.: 650.00 kW

t1-03

Motor Rated
Voltage

Sets the motor rated voltage according to the
motor nameplate.

Default

∶

200.0 V

Min.: 0.0 V
Max.: 255.0 V <3>

t1-04

Motor Rated
Current

Sets the motor rated current according to the
motor nameplate.

Default

∶

<2>

Min.: 10% of drive
rated current
Max.:200% of drive
rated current

t1-05

Motor Base
Frequency

Sets the motor base frequency according to the
motor nameplate.

Default

∶

50.0 Hz

Min.: 0.0 Hz
Max.: 400.0 Hz

t1-06

Number of Motor
Poles

Sets the number of motor poles according to
the motor nameplate.

Default

∶

Min.: 2
Max.: 48

t1-07 Motor Base Speed

Sets the motor base speed according to the
motor nameplate.

Default

∶

145 (x10 rpm)

Min.: 0 rpm
Max.: 2400 (x10 rpm)

t1-09 Motor No-Load

Sets the no-load current for the motor.

Default

∶

o2-03

Summary of Contents for EVO6000 Series







































































































Search results

Summary of Contents for EVO6000 Series

Reviews:

Related manuals for EVO6000 Series

Brands by name

Popular brands

LiteOn EVO6000 Series, Quick Start Manual

Search results

Summary of Contents for EVO6000 Series

Reviews:

Related manuals for EVO6000 Series

Brands by name

Popular brands