manualshive.com logo in svg

Lippert Components Solera 759404, Manual, Page: 9 / 12

Share
Download
Lippert Components Solera 759404 Manual Download Page 9

9

lci1.com      

574-537-8900    

 

Rev:  04.03.20

Solera

®

 Universal Hardware

Power Awning to

Solera 12V Power Awning

(For Aftermarket Application)

CCD-0001282

Wiring 

1. 

Pull the wires from the unit through the support arm 

assembly. These wires may be located at the bottom or the 

top of the support arm assembly 

2. 

Connect wiring from the unit to the switch and the 

awning drive head per the wiring diagram below 

(Fig.14)

.

NOTE: 

Check the switch. If the awning is running in 

reverse of what the switch indicates, reverse the wires.

NOTE: 

Solera Power Awning motors come stock with an 

internal 6A auto reset breaker. If this breaker trips, it will 

take approximately 30 seconds to reset. LCI recommends 

that the awning be wired into a 15A circuit.

NOTE: 

All wire to be 14 AWG or larger as necessary to 

provide 12V minimum at all times at the connection to the  

LCI-supplied power cable.

white

power

15A circuit per RVIA code 

(OEM Supplied)

ground

manual 

rocker 

switch

motor

battery, power 

source or converter

red

blue

red

black

Fig.14 

Summary of Contents for Solera 759404













Reviews:

No comments