background image

ioPower User guide                                                                                                             

Serial Command Set 

Rev. 1.41      Copyright© All rights reserved.   

Feb 2005

 

10

ioPower

 

Serial Command Set 

 

Before you use the serial command … 

(1) To use the serial commands for ioPower control, you have to 

establish a HyperTerminal 

connection between ioPower and the host PC, using a RS-232 cable for connection. 
Use the following parameters for HyperTerminal connection: 

 

Bits per seconds:

 

9600

 

 Data 

bits:

 8 

 Parity:

 None 

 Stop 

bits:

 1 

 Flow 

Control:

 Hardware 

 
(2) After your HyperTerminal session has been established, you have to 

hit the 

Enter

 key twice

 

to go into command mode

, then you can input the serial commands within the HyperTerminal 

window according to the following command usages ………………   

 

Command usage notes:

  

1. The commands are 

NOT

 case-sensitive. That means you can use lower case in typing 

your commands! The commands does not require a strict double-digit entry of bank number 
or port number (such as 

ON 01 03

 – Power on bank 1 port 3) but can accept their single-

digit entries (such as 

ON 1 3

), and also allow multiple blank spaces in between its 

command parameters (such as 

ON    1    3

).  

2. When using the HyperTerminal, note that 

ScrollLock should not be ON

. Otherwise, it 

will block you from entering commands. ScrollLock is OFF by default in HyperTerminal. 
However, if you cannot type in commands, please check the ScrollLock status, which can 
be viewed on status bar at the bottom of your HyperTerminal window. If ScrollLock is ON, 
hit ScrollLock key again to relieve it. 

 
 

HELP

 – 

Show Help Menu 

[Description]Show the Help Menu on the HyperTerminal screen 

[Usage] HELP 

[Example] Help 

 

 

? - Show Help Menu 

[Description]Show the Help Menu on the HyperTerminal screen 

[Usage] ? 

[Example] 

 

 

QUIT - Exit serial command mode 

[Description] exit serial command mode 

[Usage] QUIT 

[Example] 

QUIT

 

 
Notes: Once you exit serial command mode, you have to hit Enter twice again to enter 
the serial command mode again.   
 

Summary of Contents for ioPower

















Reviews: