Page Number - 6
Form 404372
Electric Operated Centro-Matic Pump P653S
Description
Fig. 1 Components of the P653S pump with follower
1 - Reservoir
2 - Mounting plate
3 - Pump elements
4 - Pump housing
5 - Pump outlet
6 - Relief valve
7 - Keypad
8 - Low-level control
9 - Refill Grease Fitting
connection
10 - Top Lid
11- Vent Hole
Fig. 2 Single-line pump P653S, No follower
(Note: Low-level control see Fig. 15 & 16)
Pump P653S
•
pumps greases up to NLGI 2 (per approved list) at
temperatures from -40° F to 158°F (-40°C to 70°C)
•
develop maximum pressure up to 3,500 psig (240 bar)
with pressure switch and up 4,600 psig (317 bar) with
pressure transducer.
Reservoir sizes
•
4-l transparent plastic reservoir
•
8-l transparent plastic reservoir
•
15-l transparent plastic reservoir
•
20-l transparent plastic reservoir
Electrical connection
•
For industrial 120/230 VAC applications P653S pumps
are provided with 4-pole square type connector. Electric
cable is provided by installer.
•
For mobile applications P653S pumps are equipped with
an electric cable 32 ft. (10.0 m) and 7-pole bayonet type
connector.
P653S pump is designed for single line (S) parallel Centro-
Matic type lubrication systems. The pumps integrated design
includes all necessary components to support Centro-Matic
lubrication systems:
-
controller to program and monitor lubrication cycle
-
choice of internal pressure switch or internal pressure
transducer
-
internal vent valve
-
three pumping elements connected together
-
external pressure relief valve
-
reservoir low-level control
-
end of lubrication line pressure switch or pressure
transducer choice
-
contacts for remote monitoring
-
24 VDC or 120/230 VAC power supply option, etc.
Pump can supply adequate lubricant to bearings using SL-V,
SL-V XL, SL-1, SL-32 and SL-33 injectors. Number of injectors
should be based on output of the pump being 1.5 in³/minute.
Pump for 120/230 VAC power supply can be installed in any
stationary industrial type of applications requiring lubrication
for the same number of medium size bearings.
Pump basic model can be supplied with follower plate or
without follower plate. Follower plate is recommended in
stationary industrial type applications with heavy consistency
greases (NLGI #1 and #2) and for pumps used at low
temperatures applications in all installations.
*Note: Installations using SL-32 aand SL-33 Lincoln injectors
can lubricate more than 35 bearings.
Typical Centro-Matic system schematic is shown on page 31.
CAUTION! Use only supply line hose and
fittings that are appropriate for the programmed/
set system pressure.
1 - Reservoir
2 - Mounting plate
3 - Pump elements
4 - Pump housing
5 - Pump outlet
6 - Relief valve
7 - Keypad
8 - Stirring paddle
9 - Refill Grease Fitting
10 - Stationary paddle
11 - Top Lid
Pump with Follower Plate
Pump without Follower Plate
11
████████████████████████████████████████████████████████████████████████████████████████████
Summary of Contents for Centro-Matic P653S
