Lilytech ZL-7850R, Manual

Page: 4 / 7

Suzhou Lily Tech. CO., Ltd.
Page 4, Total 7 Pages
Cool mode 【 t0 = C 】
If Room temp. ≥ Set temp. + 【 t1 】 , and Temp. Output has stopped for 【 t2 】 , then Temp. Output will be energized.
If Room temp. ≤ Set temp. , then Temp. Output will be de-energized.
Over hot protection
If Room temp. ≥ Set temp. + 【 t4 】 , then output R1 will be energized.
If Room temp. ≤ Set temp. +
【
t4
】
-
【
t5
】
, then output R1 will be de-energized.
This protection function is only effective in heat mode.
If 【 t4 】 = 【 t5 】 = 0.0, disable the protection function.
Humidity control
Humidify mode
【
h0 = H
】
If Room humidity ≤ Set humidity ( HP ) - 【 h1 】 , and Humi. Output (R2) has stopped for 【 h2 】 , then Humi. Output will be
energized.
If Room humidity ≥ Set humidity , then Humi. Output will be de-energized.
Dehumidify mode 【 h0 = P 】
If Room humidity ≥ Set humidity + 【 h1 】 , and Humi. Output has stopped for 【 h2 】 , then Humi. Output will be energized.
If Room humidity ≤ Set humidity , then Humi. Output will be de-energized.
Over wet protection
If Room humidity ≥ Set humidity + 【 h4 】 , then output R1 will be energized.
If Room humidity ≤ Set humidity +
【
h4
】
-
【
h5
】
, then output R1 will be de-energized.
This protection function is only effective in humidify mode.
If 【 h4 】 = 【 h5 】 = 0.0, disable the protection function.
Timer output R4 and R5
R4 and R5 are controlled by parameter
【
u0
】
,
【
u1
】
and
【
u2
】
.
R4 and R5 will be energized for
【
u1
】
time alternatively. A period includes an R4 energized and an R5 energized.
There is a counter counting the times of the period. Every time after the power supplied, the counting value is reset to zero.
keeping 【 S 】 and 【 ▼ 】 depressed simultaneously will show the counting value for 3 seconds.
If
【
u2
】
> 0, when the counting value reaches
【
u2
】
, R4 and R5 will stop energized, and display and will blink.
If
【
u2
】
is set to zero,R4 and R5 will never stop energized.
Forced energized manually:
Keeping
【
▲
】
depressed for 2 seconds makes R5 being energized, until the key is released.
Keeping 【 ▼ 】 depressed for 2 seconds makes R4 being energized, until the key is released.
R4 and R5 could be used for incubator egg tray control.
Alarm
High temp. alarm: if Room temp. ≥ Set temp. ( TP ) +
【
t6
】
, display “tHi”. If
【
t6
】
= 0.0, the function disable.
Low temp. alarm: if Room temp. ≤ Set temp. -
【
t7
】
, display “tLo”. If
【
t7
】
= 0.0, the function disable.
High humidity alarm: if Room humidity ≥ Set humidity ( HP ) + 【 h6 】 , display “hH”. If 【 h6 】 = 0.0, the function disable.
Low humidity alarm: if Room humidity ≤ Set humidity -
【
h7
】
, display “hL”. If
【
h7
】
= 0.0, the function disable.
Sensor
The Room temp. can be calibrated. If Room temp. is 0.2
℃
lower than real temp., set
【
t3
】
= 0.2.
The Room humidity can be calibrated. If Room humidity is 2%RH higher than real, set
【
h3
】
= -2.
When sensor fails, the Temp. and Humi. Output (R3, R2) will not be energized, and “E01” will display.
Note: do not plug in/off the sensor when power supplied.