Lightware MX8x8DVI-HDCP-Pro User Manual Download Page 9

Page: 9 / 108

MX32x32DVI-HDCP-Pro and HDMI-Pro

User’s Manual v1.0

Page 9/ 109

2.1.2.

Rear view (MX8x8DVI-HDCP-Pro)

AC Power

RS-232

DVI-D Inputs

Card activity

connector

port

1-8

LEDs

Fuse

Ethernet port

DVI-D Outputs

1-8

2.1.3. Rear view (MX8x8HDMI-HDCP-Pro)

AC Power

RS-232

Card activity

connector

port

HDMI Inputs

Input status LEDs

LEDs

Fuse

Ethernet

HDMI Outputs

S/PDIF Outputs

port

AC Power

Standard IEC power connector. The router works with
100 to 240 Volts, 50 or 60 Hz power sources.

AC Fuse

Replace with F 3.15A type only.

RS-232/422 connector

9-pole D-sub female connector. Can be ordered with RS-
232 or RS-422 control.

Ethernet port

Standard

RJ45 connector. This port can be connected to

Local Area Network.

DVI-D inputs

Standard 29-pole DVI connectors for input connections. It
accepts only digital signals.

DVI-D outputs

Standard 29-pole DVI connectors for outputs.

HDMI inputs

19-pole type A HDMI connectors for input connections.

HDMI outputs

19-pole type A HDMI connectors for output connections.

S/PDIF outputs

RCA jack connector with S/PDIF digital audio signal.
Embedded audio is still present on HDMI outputs.

Input status LEDs

Four LEDs help the signal monitoring on each HDMI
input port. They indicate the presence of power +5V, the
presence of an active video signal, HDMI mode and the
HDCP encryption status.

Card activity LEDs

These LEDs are blinking when the cards are active.

Summary of Contents for MX8x8DVI-HDCP-Pro













































































































Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands

Lightware MX8x8DVI-HDCP-Pro, User Manual

Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands