Lightware MX8x8DVI-HDCP-Pro User Manual Download Page 81

Page: 81 / 108

MX32x32DVI-HDCP-Pro and HDMI-Pro

User’s Manual v1.0

Page 81/ 109

Audio capabilities

Shows if the sink device is able to receive audio.

Supported color spaces

The supported color spaces by the sink device.

PCM frequencies

List of the supported PCM audio sample rates.

Display manufacturer

If there is a sink device attached, this field shows the
abbreviation of the device's manufacturer, as defined in
the device's EDID.

Display type

If there is a sink device attached, this field shows the
device name given by the vendor, as defined in the
device's EDID.

Display resolution

If there is a sink device attached, this field shows the
resolution of the device, as defined in the device's EDID.

Deep color support

Shows whether the display supports the 30bpp and
36bpp deep color modes or not.

YUV support in DC

If the display supports any deep color modes, this field
shows whether YUV 4:4:4 color space is supported while
using deep color formats or not.

The video signal info and audio signal info has the same fields as described in
section 5.7.1.

Summary of Contents for MX8x8DVI-HDCP-Pro













































































































Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands

Lightware MX8x8DVI-HDCP-Pro, User Manual

Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands