Lightware MX8x8DVI-HDCP-Pro User Manual Download Page 11

Page: 11 / 108

MX32x32DVI-HDCP-Pro and HDMI-Pro

User’s Manual v1.0

Page 11/ 109

2.4.

CPU-CARD

Reset

DIP

GPIO contact

DC voltage

RS-232/422

Ethernet

CPU LIVE

button

switch

closure

indicators

port

LED

In order for the MX-DVI-FR16(R) and MX-DVI-FR32R frames to work, a CPU-
CARD is needed. This card is responsible for controlling the matrix and storing all
the settings.

Reset button

Hardware reset button. Press to reset the whole frame.
Crosspoints and presets will not be reset.

DIP Switch

8-circuit DIP switch – not used in current version.

GPIO Contact closure

Relay output for alarm signaling.

DC voltage indicators

LED indicators for internal DC power voltages. All LEDs
must light continuously during normal operation.

RS 232/422 connector

9-pole D-sub female connector. Can be ordered with RS-
232 or RS-422 control.

Ethernet port

RJ45 connector. Remote control port for connecting the
unit to Local Area Network.

CPU LIVE LED

Green blinking LED indicating normal operation.

Summary of Contents for MX8x8DVI-HDCP-Pro













































































































Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands

Lightware MX8x8DVI-HDCP-Pro, User Manual

Search results

Summary of Contents for MX8x8DVI-HDCP-Pro

Reviews:

Related manuals for MX8x8DVI-HDCP-Pro

Brands by name

Popular brands