Lightware MMX6x2-HT200, User Manual

Page: 72 / 91

7. LW3 Programmers’ Reference MMX6x2-HT series – User's Manual 72
TPS Mode Setting on TPS Ports

SET•/REMOTE/ <source> | <destination> .tpsModeSetting= <TPS_mode>
HDMI Mode Settings (Output Ports)

SET•/MEDIA/VIDEO/ <out> .HdmiModeSetting= <HDMI_mode>
Audio Port Settings
Signal Source Selection

SET•/MEDIA/VIDEO/ <in> | <out> .AudioMode= <audio_mode>
Analog Audio Input Level Settings - Volume

SET•/MEDIA/AUDIO/ <in> .Volume= <volume>
Analog Audio Input Level Settings - Balance

SET•/MEDIA/AUDIO/ <in> .Balance= <balance>
Analog Audio Input Level Settings - Gain

SET•/MEDIA/AUDIO/ <in> .Gain= <gain>
Analog Audio Output Level Settings - Volume

SET•/MEDIA/AUDIO/ <out> .Volume= <volume>
Analog Audio Output Level Settings - Balance

SET•/MEDIA/AUDIO/ <in> .Balance= <balance>
Analog Audio Output Level Settings - Gain

SET•/MEDIA/AUDIO/ <out> .Gain= <gain>
Analog Audio Output Level Settings - Mute / Unmute

SET•/MEDIA/AUDIO/ <out> .MuteSetting= <logical_value>
RS-232 Port Configuration
Protocol Setting

SET•/MEDIA/UART/ <port> .ControlProtocol= <number>
BAUD Rate Setting

SET•/MEDIA/UART/ <port> .Baudrate= <number>
Databits Setting

SET•/MEDIA/UART/ <port> .DataBits= <databits>
Stopbits Setting

SET•/MEDIA/UART/ <port> .StopBits= <number>
Parity Setting

SET•/MEDIA/UART/ <port> .Parity= <number>
RS-232 Operation Mode

SET•/MEDIA/UART/ <port> .Rs232Mode= <number>
Command Injection Mode

SET•/MEDIA/UART/ <port> .CommandInjectionEnable= <logical_value>
Message Sending via Ethernet Port
Sending a TCP Message (ASCII-format) via Ethernet

CALL•/MEDIA/ETHERNET:tcpMessage( <IP_address> : <port_no> = <message> )
Sending a TCP Text (ASCII-format) via Ethernet

CALL•/MEDIA/ETHERNET:tcpText( <IP_address> : <port_no> = <text> )
Sending a TCP Binary Message (HEX-format) via Ethernet

CALL•/MEDIA/ETHERNET:tcpBinary( <IP_address> : <port_no> = <HEX_message> )
Sending a UDP Message (ASCII-format) via Ethernet

CALL•/MEDIA/ETHERNET:udpMessage( <IP_address> : <port_no> = <message> )
Sending a TCP Text (ASCII-format) via Ethernet

CALL•/MEDIA/ETHERNET:udpText( <IP_address> : <port_no> = <text> )
Sending a UDP Binary Message (HEX-format) via Ethernet

CALL•/MEDIA/ETHERNET:udpBinary( <IP_address> : <port_no> = <HEX_message> )
Message Sending via RS-232 Serial Port
Sending a Text (ASCII-format) via Serial Port

CALL•/MEDIA/UART/ <port> :sendText( <message> )
Sending a Binary Message (HEX-format) via Serial Port

CALL•/MEDIA/UART/ <port> :sendBinaryMessage( <message> )
Sending a Message (ASCII-format) via Serial Port

CALL•/MEDIA/UART/ <port> :sendMessage( <message> )
Infrared Port Configuration
Enable Command Injection Mode

SET•/MEDIA/IR/ <source> | <destination> .CommandInjectionEnable= <logical_value>
Enable/Disable Output Signal Modulation

SET•/MEDIA/IR/ <destination> .EnableModulation= <logical_value>
Change Command Injection Port Number

SET•/MEDIA/IR/ <source> | <destination> .CommandInjectionPort= <port_no>
  
